1. Interpreting Demand and Capacity for Street and Highway Design Lecture 6 CE 5720 Norman Garrick Norman W. Garrick

2. Travel Flow Data Some Basic Concepts Good travel flow data for all modes of travel is important for transportation design. One of the challenges is that travel flow varies significantly in both space and time. We often do not have data at a fine enough resolution to fully capture these variations. It is important to understand the likely variations in order to effectively interpreter the available data

3. Norman W. Garrick Temporal Variation in Traffic Flow Traffic flow vary by time of day, day of week, month of year and from year to year. The pattern of variation depends on the specific location. For example, the temporal variation of traffic in Storrs is likely to be different from that in Willimantic. Monday to ThursdaySaturday http://www.ptt.uni-duisburg.de/en/projekte/babnrw/daten/

4. Norman W. Garrick Temporal Variation in Traffic Flow One solution that is some times used to reduce temporal variation is differential pricing. For example, many transit systems charge a higher rate for travel before 10 am and after 3 pm. This helps encourage people that have flexible plans to delay their travel to the off peak time. This is the same approach used on some toll roads where the plan is know as congestion pricing.

5. Norman W. Garrick Spatial Variation in Traffic Flow http://www.interstate-guide.com/images/i-077_va_aadt.gif

6. Norman W. Garrick Directional in Traffic Flow Directional Variation Reversible lanes in the middle to deal with a severe directional variation. (I believe this is just conceptual – I don’t know of any example of reversible lanes implemented in this manner.

7. Norman W. Garrick Directional Distribution In many urban areas trips are mostly going towards the central business district in the morning and from the CBD in the evening. This means that the trains and the roads are sized to carry the peak direction flow. If the directional distribution is very lopsided then this is a very inefficient system since the lanes and the trains going away from the center will be virtually empty in the morning. One argument for mixed land use is that it helps to cut down on this directional over balance. So if a train is connect two mixed use centers (such as downtown DC and Arlington, Virginia) the directional distribution will be more balanced resulting in more efficient use of the transportation system.

8. Norman W. Garrick Where does travel flow counts come from? State Counts of Vehicle Traffic The DOT maintain a program for counting traffic on all state owned highways, roads and streets. There are two different type of counts: permanent count stations and temporary count stations Permanent Count Stations give the most complete coverage of temporal variation in traffic Temporary count stations are much less reliable since they are put out for at most 48 hours – the state then use factors to estimate the average daily count. Other source of traffic count data are counts from individual towns or from developers working on larger projects.

9. Norman W. Garrick Where does travel flow counts come from? Pedestrian, Bikes and Transit Counts I know of no agencies that routinely count pedestrian traffic – this makes it harder to include pedestrian issues in transportation planning A handful of cities in the country, including Portland, Davis and Cambridge have programs for counting bike traffic Transit counts are readily available from transit agencies and national transit bodies

10. Bikeway MilesCyclists per Day 19912007 Portland (OR) Bike Count Program http://www.streetsblog.org/wp-content/uploads/2007/09/portland_bike_counts.jpg

11. Norman W. Garrick Shared Bikes, Paris A New Era for Bike Counts http://networkedblogs.com/g0g87 (from Sam Goater) http://networkedblogs.com/g0g87

12. Norman W. Garrick Bike Parking at Train Station, Amsterdam

13. Norman W. Garrick What is the State Traffic Counts Used for? AADT The state traffic count is used to estimate an average annual daily traffic (AADT) The AADT is meant to represent the average traffic over all 365 days in the year. In other words, it is meant to be Total Traffic in year / 365 This can be obtained relatively accurately from the permanent count stations. From the temporary stations, this is more difficult. The count from the station (which is referred to as average daily traffic or ADT) is multiplied by seasonal and day of the week adjustment factor to get an estimated AADT.

14. Norman W. Garrick Characterizing Traffic Counts Vehicles/hr or AADT Often reports from state level traffic count studies give average annual daily traffic (AADT) Since hourly volume for the design hour is what is typically used for design it is left up to the designer to come up with a reasonable design hourly volume from the AADT As a very rough guide the typical design hour volume is can be taken as about 10% of the AADT. But this % varies significantly depending on the temporal variation in traffic. Once a design hour volume is determined then the designer must also determine the directional split.

15. Demand and Capacity for Street and Highway Design Convention street and highway design is based on the idea of fitting capacity to demand Demand is characterized by a design hour volume Capacity is characterized by design hourly service volume Norman W. Garrick

16. Demand The design hour volume is meant to be the volume of traffic that will use the facility in the design hour, in the design direction, in the design year Usually the design hour is taken as the 30 busiest hour of the year DHV is often estimated from AADT Norman W. Garrick

17. Estimating Traffic in the Design Year In many projects, the DHV is based on traffic for 20 or 30 years in the future The procedure for doing this is some times derided as ‘predict and provide’ because in many cases it is based just on predicting past trends Norman W. Garrick

18. Problems with Predict and Provide Predict and provide is problematic because expanding capacity affects future demand – therefore, using past trends to predict future traffic volumes is an invalid procedure What are some of the factors that affect future travel? Norman W. Garrick

19. Capacity Norman W. Garrick What is the capacity of a street or highway? By Ian Lockwood

20. New View of Street Capacity In the past, Street Capacity = Design Hour Service Volume Now, Street Capacity = Social Capacity + Economic Capacity + Travel Capacity Norman W. Garrick By Ian Lockwood

21. Understanding Capacity for Vehicle Travel The design has flexibility in selecting a design capacity She does this by designating a Level of Service Once a LOS is determined then the design hourly service volume can be selected from a chart Norman W. Garrick Determining vehicle capacity on a street is not really like determining the amount of water in a measuring jar Capacity is not a fixed number – it is rather a number selected based on what level of congestion we are willing to put up with

22. LOS for Freeways LOS in urban areas is usually based on intersection flow Norman W. Garrick

23. Capacity and the Level of Service Some cities now require that we design for LOS E or F to reduce inefficiency and the impact on the urban area of having large facilities Norman W. Garrick Selecting a low LOS means that you are designing for a low level of congestion during the busiest hour of the year That means the facility will be empty for most hours in the day

25. Why is this Road So Empty? 1.Predict and provide for 30 year in future 2.Design for 30th busiest hour of year 3.Design using a capacity based on low LOS