1. ECE 477 Design Review Team 5  Fall 2009 Ben Carter – Jacqui Dickerson – Ian Oliver – Dennis Lee

2. Outline Project overviewProject overview Project-specific success criteriaProject-specific success criteria Block diagramBlock diagram Component selection rationaleComponent selection rationale Packaging designPackaging design Schematic and theory of operationSchematic and theory of operation PCB layoutPCB layout Software design/development statusSoftware design/development status Project completion timelineProject completion timeline Questions / discussionQuestions / discussion

3. Project Overview Next generation communication system for vehicles – –Simple, real-time visual communication Multi-touch input – –Driver’s gestures produce an output on LEDs around the perimeter of a car Color-coded messages – –Tri-color LEDs produce blue, green, yellow, orange, and red outputs

4. Project-Specific Success Criteria 1. The ability to determine direction of a finger sweep on a touch pad array.1. The ability to determine direction of a finger sweep on a touch pad array. 2. The ability to determine the number of fingers used on a touch pad array.2. The ability to determine the number of fingers used on a touch pad array. 3. The ability to produce at least two meaningful LED patterns.3. The ability to produce at least two meaningful LED patterns. 4. The ability to determine force of acceleration on a car.4. The ability to determine force of acceleration on a car. 5. The ability to wirelessly transmit data from the multi- touch signal processor to the LED cluster controllers5. The ability to wirelessly transmit data from the multi- touch signal processor to the LED cluster controllers

5. CapSense Controller 0 Microcontroller/DSP (Gesture Recognition) 30 Capacitive Touch Inputs 30 CapSense Controller 1 30 Capacitive Touch Inputs 30 CapSense Controller 7 30 Capacitive Touch Inputs 30 CapSense Controller 8 30 Capacitive Touch Inputs 30 I2C RF Transmitter LED Driver 0 Microcontroller 0 (LED Control) 15 LED Driver 13 15 12 more 5 tricolor LEDs I2C RF Receiver RF Communication @ 315MHz LED Driver 0 15 LED Driver 3 15 2 more 5 tricolor LEDs I2C Accelerometer 5 More UART Tx UART Rx 0V – 5V analog

6. Component Selection Rationale dsPIC33FJ256MC710dsPIC33FJ256MC710 –Required a lot of RAM & moderate Flash –Availability w/ many suppliers PIC18F2525PIC18F2525 –Required I2C interfacing & sizeable Flash –dsPIC chosen; staying w/ same family LED Drivers (TLC59116)LED Drivers (TLC59116) –Required 15 PWM channels to control 5 tri- color LEDs –Ability to control up to 16 PWM channels

7. Component Selection Rationale RF Transmitter/Receiver (MO-SAWR- AS315M/MO-RX3400-A315M) – –Required 315MHz – –Provides up to 100m of transmission Accelerometer (MMA1270EG) – –Required 2.5g over 3 axes at 5V – –SOIC packaging for ease of soldering Capacitive Touch Input Controllers (CY8C20666Capacitive Touch Input Controllers (CY8C20666) – –Required multiple touches to be realized – –Donated by Purdue Alum & Cypress FAE

8. Packaging Design Constraints Will not be demonstrating on a full size vehicleWill not be demonstrating on a full size vehicle –Large RC car will house one LED Output Cluster –User Interface Module will be exterior to car, powered by an AC wall wart Full size design would consist of several LED Output Clusters, weatherproofing, and a scheme for mounting the User Interface Module to a steering wheelFull size design would consist of several LED Output Clusters, weatherproofing, and a scheme for mounting the User Interface Module to a steering wheel

9. Packaging Design – User Interface Module 8”x8”x1-1/2”8”x8”x1-1/2” –*variable 20 user feedback LEDs replicate LED output on RC car20 user feedback LEDs replicate LED output on RC car Front will be denoted with a print of a black & white top- view sketch of a carFront will be denoted with a print of a black & white top- view sketch of a car 5”x6” capacitive touch area is uncovered PCB5”x6” capacitive touch area is uncovered PCB External 2” antenna for RF transmission to RC carExternal 2” antenna for RF transmission to RC car

10. Packaging Design - LED Output Vehicle 32”x12”x10”32”x12”x10” 12 LEDs for front/back12 LEDs for front/back 23 LEDs for sides23 LEDs for sides –=>70 tricolor LEDs –~1LED per 1.5” LEDs mounted on 5 apiece on 14 PCBsLEDs mounted on 5 apiece on 14 PCBs LED Panel PCBs mounted on inside of car’s exterior plasticLED Panel PCBs mounted on inside of car’s exterior plastic Holes will need to be drilled through car’s exterior for LEDs to show throughHoles will need to be drilled through car’s exterior for LEDs to show through LEDs will extend ~3/4” off PCB, so will be able to flex and fit throughLEDs will extend ~3/4” off PCB, so will be able to flex and fit through

11. Schematic/Theory of Operation duplicate this slide as necessary for each major block of your designduplicate this slide as necessary for each major block of your design

12. Schematic/Theory of Operation Capacitive sensor is a pair of plates/electrodesCapacitive sensor is a pair of plates/electrodes There is also capacitance between finger and electrodesThere is also capacitance between finger and electrodes A sensor detects change in capacitance when finger is presentA sensor detects change in capacitance when finger is present

13. Schematic/Theory of Operation Capacitive buttons are on one side of the boardCapacitive buttons are on one side of the board The microcontroller (PSoC) is on the other sideThe microcontroller (PSoC) is on the other side A plastic/glass overlay (1-5mm thick) covers buttonsA plastic/glass overlay (1-5mm thick) covers buttons

14. Schematic/Theory of Operation The capacitive sensing microcontroller is the PSoCThe capacitive sensing microcontroller is the PSoC Each PSoC can scan buttons and communicate over I2CEach PSoC can scan buttons and communicate over I2C Our PSoC will communicate with a DSP to process inputsOur PSoC will communicate with a DSP to process inputs

15. Schematic/Theory of Operation Flow of input to output:Flow of input to output: –CapSense microcontroller (PSoC) reads input from buttons – 9 PSoCs to sense 120 buttons total –DSP (dsPIC) reads PSoCs to interpret input, sends commands to LED controller wirelessly –LED controller (PIC18) coordinates LED drivers to produce output patterns

16. dsPIC RST to PSoCs I2C to PSoCs and TLC RF Tx to PIC18

17. PCB Layout – TLC Board Main ComponentsMain Components –5 LEDs and a single TLC driver chip Other ComponentsOther Components –5 Resistors, 5 Headers, 1 Capacitor 0.5” x 5”0.5” x 5” Tight space required careful routing Tight space required careful routing

18. PCB Layout – TLC Board

19. PCB Layout – PIC18 Board Main ComponentsMain Components –PIC18, RF Receiver, Power Supply Other ComponentsOther Components –Switch, 18 Headers, 3 Resistors, 4 Capacitors, 1 Inductor, and 1 Diode 1.4” x 5”1.4” x 5” Plenty of space allowed for easy routing and the ability to actually minimize the area of the board Plenty of space allowed for easy routing and the ability to actually minimize the area of the board

20. PCB Layout – PIC18 Board

21. PCB Layout – dsPic Board Main ComponentsMain Components –dsPIC, RF Transmitter, Power Supply Other ComponentsOther Components –10 Capacitors, 16 Resistors, 1 Switch, and 17 Headers 2” x 7” section of the larger User Interface Board2” x 7” section of the larger User Interface Board Lots of space allowed for large heat sink and ease of routing Lots of space allowed for large heat sink and ease of routing

22. PCB Layout – dsPic Board

23. PCB Layout – MultiTouch Board Main ComponentsMain Components –1 Cypress PSOC chip and 30 CapSense Pads Other ComponentsOther Components –34 Resistors, 2 Headers, 1 Capacitor, and 1 OR gate 5” x 6” Section of the larger User Interface Board5” x 6” Section of the larger User Interface Board Via on each CapSense pad made routing very difficult Via on each CapSense pad made routing very difficult

24. PCB Layout – MultiTouch Board

25. Software Design/Development Status PIC18F(LED Output Controller)PIC18F(LED Output Controller) –LED Output Coordination Establishing Timer0 interrupts, I2C interfaceEstablishing Timer0 interrupts, I2C interface dsPIC33F(Multiple Touch Processor)dsPIC33F(Multiple Touch Processor) –Finger Count Detection Area vs. discrete contactsArea vs. discrete contacts –Direction Vector Calculation Track angle of finger swipeTrack angle of finger swipe CY8C(CapSense Controller)CY8C(CapSense Controller) –Activation of CapSense block, record data, then communication of data over I2C

26. Project Completion Timeline Week 8 Week 9 Week 10 Week 11 Week 12 Week 13 Week 14 Week 15 Week 16 12-Oct19-Oct26-Oct2-Nov9-Nov16-Nov23-Nov30-Nov7-Dec Design Review Proof of Parts Constr. LED Output Controller PCB Constr. LED Panel PCB Constr. User Interface Module RC Car Construction LED Output Interface Software LED Output Coordination Software CY8C CapSense Software User Module Interface Software Multiple Touch Finger Detect Software Multiple Touch Direction Vector Software

27. Questions / Discussion