1. Introduction to Sequential Logic Design Flip-flops FSM Analysis

2. Prev… Latches S-R S-bar-R-bar S-R with enable signal D

3. D latch D C Q Q

4. D-latch operation When C is asserted, Q follows the D input, the latch is “open” and the path (D-->Q) is “transparent”. When C is negated, the latch “closes” and Q retains its last value.

5. D-latch timing parameters Propagation delay (from C or D) Setup time (D before C edge) Hold time (D after C edge)

6. S-R vs D latches S-R Useful in control applications, “set” and “reset” S=R=1 problem Metastability problem when S, R are negated simultaneously, or a pulse applied to S, R is too short. D Store bits of information No S=R=1 problem Metability still possible.

7. FF vs. Latch Latches and flip-flops(FFs) are the basic building blocks of sequential circuits. latch: bistable memory device with level sensitive triggering (no clock), watches all of its inputs continuously and changes its outputs, independent of a clocking signal. flip-flop: bistable memory device with edge-triggering (with clock), samples its inputs, and changes its output only at times determined by a clocking signal.

8. Edge triggered D Fli-Flop A D FF combines a pair of D latches. Master/slave D FF Positive-edge-triggered D FF Negative-edge-triggered D FF Edge-Triggered D FF with Enable Scan FF

9. Positive-Edge-triggered D flip-flop Dynamic-input indicator

10. Edge-triggered D flip-flop behavior

11. D flip-flop timing parameters Propagation delay (from CLK) Setup time (D before CLK) Hold time (D after CLK)

12. D FF with asynchronous inputs Force the D FF to a particular state independent of the CLK and D inputs. PR (Preset) and CLR (Clear)

13. Negative-edge triggered D FF Simply inverts the clock input. Active low.

14. Edge-triggered D FF with Enable

15. Scan flip-flops -- for testing TE = 0 ==> normal operation TE = 1 ==> test operation All of the flip-flops are hooked together in a daisy chain from external test input TI. Load up (“scan in”) a test pattern, do one normal operation, shift out (“scan out”) result on TO. Scan FF

16. J-K flip-flops Not used much anymore

17. T (toggle)flip-flops A T FF changes state on every tick of the clock. (be toggled on every tick) Q has precisely half the frequency of the T. Important for counters, frequency dividers Positive-edge-triggered T FF

18. T (toggle)flip-flops with enable

19. Clocked Synchronous State-Machine State machine: generic name for sequential circuits;(Finite State Machine:FSM) Clocked: the storage elements(FFs) use a clock input; Synchronous: all of the FFs in a circuit use the same clock signal. Such a FSM changes states only when a triggering edge(rising or falling) on the clock signal.

20. State Machine Structure State memory: n FFs to store current states. All FFs are connected to a common clock signal. Next-state logic: determine the next state when state changes occur; Output logic: determines the output as a function of current state and input Mealy machine vs. Moore machine

21. Mealy Machine Next state= F (current state, input) Output= G(current state, input)

22. Moore Machine Next state= F (current state, input) Output= G(current state)

23. Characteristic Equations A Characteristic equation specifies the FF’s (or latch’s) next state as a function of its current state and inputs.

24. Analysis of FSM with D FFs Next state= F (current state, input) Output= G(current state, input) Step 1: Determine the next-state and output functions F, G Step 2: Use F, G to construct a state/output table that completely specifies the next state and output of the circuit for every possible combination of current state and input. Step 3: (optional) Draw a state diagram which is a graphical form of the state/output table.

25. Example: clocked synchronous FSM using positive-edge triggered D FFs

26. Transition, state, state/output tables Excitation equations Transition Equations (next-state equations) Output equations

27. State Diagram

28. Summary: how to analyze a clocked symchronous state machine? 1) Determine the excitation equations for the FF control inputs; 2) Substitute the excitation equatiions into the FF characteristic equations to obtain transition equations; 3) Use the transition equations to construct a transition table; 4) Determine the output equations; 5) Add output values to the transition table for each state (Moore) or state/input combination (Mealy) to create a transition/output table; 6) Name the states and substitute state names for state-variable combinations in the transition/output table to obtain state/output table; 7) Draw a sate diagram corresponding to the state/output table.