1. Section 9: Implementing the Network CSIS 479R Fall 1999 “Network +” George D. Hickman, CNI, CNE

2. Objectives Plan the network and install network cabling Install and configure network interface boards (NICs) Install and configure hard disk drives Install workstation operating systems Install network client software

3. Plan the Network What type of cabling will you use? Is there equipment in the building that can impact the network (by putting off EMI, etc.) Install cabling in areas where it won’t be damaged (not under a rug or in a walkway)

4. Network Cable If you make your own, use proper parts and techniques –Category 3 cable on a 100 Mbps network is not the best choice Watch your lengths –97 M run up to the wall jack, don’t use a patch cable over 3 M

5. Crimping UTP Cable Strip off no more than ¾ inch of outer sheathing to expose the twisted pair wires Untwist the pairs about ½ inch –Don’t untwist more than ½ inch, or you may introduce crosstalk Arrange colors appropriately –White/Orange, Orange, White/Green, Blue, White/Blue, Green, White/Brown, Brown

6. Crimping UTP Cable (Con’t) Cut the wires to the same length, just long enough to reach the end of the RJ45 connector (Spring lever down) Push the wires into the connector –Verify they are still in the correct order Crimp the wires down VERIFY THE CABLE

7. Install / Configure NICs Manually configured –DIP switches or Jumpers Software configured –Executable file to configure settings Plug-n-play –Self configuring (if PnP OS/BIOS/Cards)

8. Choosing the NIC PC Bus or Architecture –ISA pg 9-10 –MCA pg 9-11 –EISA pg 9-12 –VLB pg 9-13 –PCI pg 9-13 –PCMCIA pg 9-15 Network Topology –Ethernet –Token Ring –FDDI

9. Configuration Information IRQ (hardware interrupts) –Interrupt ReQuest Channel –Lets the System Board know the device needs something –CPU will put other work on hold to respond to an IRQ –Interrupts cannot be shared by 2 devices (except on MCA, EISA, or PCI systems) –Common IRQs Table 9-2 page 9-17 DMA support –Direct Memory Channel –Allows certain devices to write data directly to system memory without CPU intervention –Common DMAs Table 9-3 page 9-18

10. Configuration Information (Con’t) I/O address (port) –A Range of addresses in memory reserved by the CPU –Each range is assigned to a device, to “drop off” data for the CPU to process –If addresses overlap, errors result –Commonly used I/O Addresses Table 9-4 Page 9-19 Memory address –Base Memory or Shared Memory –ROM on the card, needs to control some RAM too –If addresses overlap, errors result –Commonly used Base Addresses Table 9-5 Page 9-20

11. Jumpers / DIP switches Jumpers –Page 9-21, Figure 9-9 –Jumpers close the circuit between pins DIP Switches –Page 9-21, Figure 9-10 –ON or OFF, not always labeled which way is which

12. Software-configured Cards MCA –Micro Channel Architecture –Comes with IBM Reference Disk –Software adjusts settings to avoid conflicts EISA –Extended Industry Standard Architecture –EISA Configuration Utility –Software reads “.cfg” files and adjusts settings to avoid conflicts –Verification Mode and Lock/unlock modes

13. ISA and VLB boards Some are software-configurable, others use DIP or jumpers, or are plug and play ISA is 8 or 16-bit VLB is 32 bit card

14. Plug-n-Play PCI PCMCIA (PC card) ISA MCA Requires: –PnP BIOS –PnP card –PnP OS

15. Hard Disk Drives “provides data storage and data retrieval....with total reliability, at the highest possible speed, and at a reasonable cost” See figure 9-12 on page 9-29

16. Disk Interface Type IDE (Integrated Device Electronics) –RLL encoding, on-disk controller –No CD support or drives over 528 MB –40 pin connector cable Enhanced IDE (EIDE) –Drives over 528 MB, CD support –Up to 16.6 MB / second –Up to 4 devices –40 pin connector cable

17. SCSI flavors Small Computer Systems Interface SCSI –7 devices –5 MB/second transfer on 8-bit bus SCSI-II –50 pin connector –Fast SCSI-II and Wide SCSI-II –20 MB / second 16 or 32-bit bus

18. SCSI (Con’t) SCSI-III –Ultra SCSI –40 MB /second –32 bit bus –31 devices on 32 bit bus

19. SCSI Connectors SCSI –25-pin SCSI-II –50-pin Fast SCSI-II –50-pin Wide SCSI-II –68-pin Fast Wide SCSI-II –68-pin Ultra SCSI-III –50 and 68 pin

20. Hard Disk Tips Don’t bump or shake a moving drive 95 % of SCSI problems are wrong termination or ID settings A second drive on same controller can save $$, but costs performance SCSI controllers establish connection with each device at boot up, causing a delay during POST Route cables (esp. SCSI) carefully—avoid noise or rolling cable back on itself Parallel to SCSI adapters work, but SLOW

21. Installing SCSI Disk Plan the SCSI bus Configure and install the HBA Configure and install the disk Attach cables to the disk Set CMOS disk type to “0” “Not Installed” or “SCSI” Complete disk configuration and termination

22. Planning the SCSI Bus Termination –Both ends of chain must be terminated SCSI Addresses –Each device must have unique ID –HBA usually 7 –0 is highest priority, 6 lowest priority (non MCA) Cabling –6 meter maximum –Pin 1 is colored stripe

23. Configuring / Installing the HBA Set SCSI address Set termination where necessary Configure –Controller interrupt –Base memory –Base I/O address –DMA channel

24. Configure / Installing SCSI Disks Set SCSI address Set termination where necessary Some disks do this automatically Attach cables –Pin 1 on disk(s) and HBA have red stripe Set CMOS type –“0”, “Not Installed”, or “SCSI”

25. Installing IDE Hard Disk Drives Configure / Install IDE Card (if not on board) –Controller is on the HDD, but the expansion card is often called the controller Configure / Install hard disk –Single, Master, or Slave, Primary or Secondary Attach cables to the disk –40 pin cable, 18 inch max length. Pin 1 is Red stripe Set CMOS disk type –Cylinders, heads, Sectors/track, Write Precomp –Auto Detect –User defined

26. Preparing Hard Disks for Use Create partitions –Divide disk into logical units –Can be one partition per OS –Partition table at start of disk, then partition(s) Perform high-level format –Identifies bad sectors –Creates Boot sector / FAT / Blank root directory –Optionally copy system files –Used when you want to install new OS –Used when you want to completely erase a disk

27. Network Clients Software that runs on the client that allows allows a connection to a server Windows 98 clients –MS client for Microsoft Networks To Connect to Win NT or other Windows w/s –MS Client for NetWare Networks To Connect to NetWare server in bindery mode –MS Client for Banyan Vines To Connect to Banyan Vines server Novell Client for Windows –Allows NDS connection to NetWare 4.x + networks