1. Performed by: Yaron Recher & Shai Maylat Supervisor: Mr. Rolf Hilgendorf המעבדה למערכות ספרתיות מהירות הטכניון - מכון טכנולוגי לישראל הפקולטה להנדסת חשמל Technion - Israel institute of technology department of Electrical Engineering Sub -Nyquist Sampling System Architecture סמסטר אביב 2010 High speed digital systems laboratory Characterization presentation

2. Project Overview Design system architecture Creating debug environment Architecture implementation on FPGA Creating controlling GUI

3. General Algorithm Scheme Expand block: Recieves 4 channels from A/D and expands them to 12 channels (18bit each) **Implemented in the same FPGA CTF block: Discovers supports out of 12 channels (support width 7 bit) DSP & Detector block**: Reconstructs the Initial Signal

4. 1x BOARD: ProcStar||| GiDEL 4x FPGA: Stratix||| EP3SE110 Altera Overview FPGA Environment

5. PROCStar III Processing unit

6. Buses on Board FPGA to FPGA Bits Max.Freq.(MHz)  L/R (I/O) :100 250// exp. IC4  V18_L/R :10 300  Main:40 300// global FPGA to PSDB Bits Max.Freq.(MHz)  L/R_IO :20 300// 7 to IC1  L_IN:8 300// PSDB to IC  L2_IO:85 300// only to IC1

7. Memories External from FPGA  Bank A:256 MB DDR2 DRAM  Bank B,C:2 x 1 GB SODIMM Internal inside FPGA  MLAB 640-bit (639 blocks) Filter delay lines, small FIFO buffers and shift registers  M9K Blocks 9,216-bit (16 blocks) General purpose memory applications  M114K Blocks 147,456-bit (2150 blocks) Processor code storage, packet and video frame buffering. Max.Freq.=333MHz B Max.Freq.= 333MHz C Max.Freq.=166MHz Max.Freq.=500MHz Total Internal Memory: 1MByte

8. Project Goals Integrate Designs – Across linked FPGA’s Set and support Test environment Design and Implement Debug GUI Improve Debug GUI to work environment GUI

9. General Connectivity

10. 1.Loading data on board FIFOs from PCI 2.Loading control registers from PCI 3.Transferring data to internal RAMs from external memory 4.Sending Start Loading signal to CTF/DSP/Exp. Units 5.Receiving Ready signal from the CTF/DSP/Exp. Units 6.Sending Ready signal to the main controller. All units ready 7.Main controller Starts the A2D and the system runs Process Flow Similar to all Units

11. Expander Entity Inputs: Clk_60 – 60MHz input data clock Clk_20 – 20MHz main output data clock Clk_2 – 2MHz iteration output data clock Clk_240 – 240MHz processing clock From main controller : rst – reset start_load – memory ready for read num_of_itr – number of wanted slice pause – pause the system From CTF : req_pulse – request of new slice Memory (20[MHz]) : memory_data – data from memory memory_ack – requested data is ready From A/D (60[MHz]) : Data_from_AD – input data for the system Data_in_valid – the input is valid Outputs: ready_to_arch – finished initilization data_to_main – main output to CTF/DSP (20[MHz]) data_to_main_valid – main output is valid data_to_CTF – iteration output (2[MHz]) data_to_CTF_valid – iteration output is valid memory_read_request – request data from memory

12. Expander Blocks Including on Board Memories A2D : FIFO on board memory Coeff. :FIFO on board memory Main Bus Debug:FIFO on board memory CTFDebug: FIFO on board memory A2D Reader:Reads data from A2D, simulates A2D input Main Debug Writer:Writes data from main bus to on board FIFO CTF Debug Writer: Writes data from Expander to debug memory Main Bus Interface:Receives data from Expander & sends with high rate CTF Bus Interface:Receives data from Expander & sends with high rate Main Controller:Controls the system operation Registers: Contain control data received from PCI Pll:On board Pll, similar to all Block Description

13. Expander Block Diagram

14. Expander State Machine

15. CTF Entity Outputs: To Controller : ready – ready to begin To Expander : req_pulse – requests next iteration To DSP : support – numbers of support num_of_supports – total number of supports support_valid – support data is valid To Matrix RAM : A_addr – Address for data from RAM A_rd_req – read enable Inputs: Clk_20 – 20MHz main input data clock Clk_240 – 240MHz processing clock CLk 160 - 160MHz processing clock or as needed From controller : reset – reset start_load– memory ready for read pause – pause the system N_Frame– Frame Threshhold - OMP stopping cond. Num_Of_Ite r- Number of iterations From Expander : data_from_exp – iterational data data_exp_valid - iterational data valid From DSP : initiate – there has been support change From Matrix RAM: A_data – data from RAM From Main interface: data_main– input data for the expander data_main_valid– the data is valid

16. CTF Blocks Including on Board Memories Iteration Debug : FIFO on board memory Matrix :FIFO on board memory Memory Debug :FIFO on board memory Matrix internal : RAM memory Main Reader :Reads data from memory, simulates input from Exp. main Exp.Debug Reader : Reads data from memory, simulates input from Exp. L/R Matrix Writer : Reads ‘A’ matrix from memory, writes to internal memory Memory Debug Writer: Writes Debug data to memory Main Bus Interface :Receives data from main bus & sends with low rate CTF Bus Interface :Receives data from L/R bus & sends with low rate Exp. DebugMod. :Simulates Expander in debug mode Dsp DebugMod :Simulates DSP in debug mode Main Controller :Controls the system operation Registers : Contain control data received from PCI Block Description +CTF to DSP

17. CTF Block Diagram CTF to DSP interface

18. CTF State Machine

19. DSP Entity Outputs: column_number– number of column digital_signals – data output samples_valid_out– the output data is valid support_changed– support change was detected Inputs: Clk_20 – 20MHz main input data clock Clk_240 – 240MHz processing clock From controller : reset – reset start– memory ready for read pause – pause the system From CTF : support – numbers of support support_num – how many support passed support_valid – support number is valid Internal FIFO: samples_from_fifo– data from fifo samples_fifo_valid– the data is valid From Main interface: samples_from_expander– input data for the expander samples_expander_valid– the data is valid From Matrix memory: memory_get – matrix row

20. DSP Blocks Including on Board Memories MainBus : FIFO on board memory Matrix :FIFO on board memory Delay:FIFO on board memory Output:FIFO on board memory Matrix internal: RAM memory Main Reader:Reads data from memory, simulates input from Exp. Main Matrix Writer: Reads ‘A’ matrix from memory, writes to internal memory Output Writer: Writes outputdata to memory Fifo Reader:Reads inputdata from delay fifo Main Bus Interface:Receives data from main bus & sends with low rate Ctf DebugMod.:Simulates CTF in debug mode Main Controller:Controls the system operation Registers: Contain control data received from PCI Block Description +DSP to CTF interface

21. DSP Block Diagram DSP to CTF interface

22. DSP State Machine

23. Studying each group Entity’s I/O and single Debug mode operations (from Dima and Oleg) Studying Board busses, memories and communication clocks phase\skew problem (Gadi’s Project handle it) Design and Implement the communication blocks (Interface blocks) needed for the across linked FPGA’s- and the same time to be able to support groups with 1 FPGA Debug mode operation. Debug entire board+ all group’s Entity’s, we will held continuous meetings with the groups to synchronize with them and update them with the needed architecture changes. (each change they might have need to be informed and confirmed with us) Design and Implement Debug GUI (Visual C? JAVA? LabView?)- creating the test environment Improve GUI for board users Future Aspirations

24. Gantt Chart

25. project part B (Not in the Gantt…) Exams period B…  Test and Debug Entire Board Finish GUI Test Environment Improve GUI to System controlling GUI

26. Questions?