1. Closed loop control

2. Closed loop speed control of VSI drives

4. Closed loop speed control of CSI drives

6. Rotor side speed control
Stator side control is applicable to both squirrel cage & SRIM
Because of more advantages
Squirrel cage motor is always preformed
rotor side control – the speed control of slip ring IM

7. Disadvantages Wound rotor machines is heavier High cost
High rotor inertia
High speed limitation
Maintenance & reliability problems due to brushes and slip rings.

8. SRIM speed control method is very simplest and oldest method.
The speed can be controlled by mechanically varying rotor circuit rheostat.
The main feature of this m/c is that slip power becomes easily available from the slip rings.
Which can be electronically controlled to control speed of the motor.

9. Applications of slip power recovery drives are,
Variable speed wind energy system
Large capacity wind energy system
Variable speed hydro pumps / generators

10. Rotor resistance control

11. By varying the rotor circuit resistance R2
3Φ AC supply is fed to the stator and a variable resistance R2 is connected in the rotor side.
By varying the rotor circuit resistance R2
The starting torque & starting current can be controlled.

12. N – T char., of rotor resistance control

13. Speed – Stator current char.,

14. In this curve, N – Is curve
By increasing rotor circuit resistance , Tm remains constant but Tst increases N decreases.
N – Is curve
By increase rotor circuit resistance, Is decreases, N decreases

15. Drawbacks
Reduced efficiency because the slip energy is wasted in the rotor circuit resistance.
Unbalance in voltage & current.

16. Advantages High line power factor Absence of line current harmonics
Smooth & wide range of speed control

17. SRIM speed control with rotor circuit chopper (or) static rotor resistance control

18. The speed can be varied by varying the rotor circuit resistance
The rotor resistance can be varied sleeplessly by using a diode bridge rectifier & chopper as shown below.
This method of speed control is very inefficient because slip energy is wasted in rotor circuit resistance

20. Line power supply is given to the stator of m/c and
Advantages: high starting torque is available at low starting current & improved power factor
Line power supply is given to the stator of m/c and
Rotor circuit, slip voltage is available across the slip rings.
This slip voltage is rectified by the 3Φ diode bridge rectifier.
The dc voltage is converted to current source Id by connecting a large series inductor Ld

21. It is then fed to shunt chopper with resistance R,
The chopper circuit may use IGBT , GTO, thyristor (or) any other power semiconductor devices.
Here the dc chopper circuit consists of an IGBT.
The chopper periodically connects and disconnects the resistance R.

22. When the IGBT chopper is on
Resistance is short circuited & the current Id is passed through it i.e, Vdc = Vd = 0 and R = 0

23. When the I G B T chopper is off
The resistance is connected in the circuit & the dc link current Id flow through it.
i.e., Vdc = Vd and resistance in the rotor circuit is R.

25. Re varied by varying duty cycle of the chopper
Therefore the developed torque and speed of the m/c can be controlled by the variation of the duty cycle of the chopper.

26. Slip power recovery system
This system is mainly used for speed control of SRIM
The speed of SRIM can be controlled by varying the stator voltage (or) by controlling the power flow in the rotor circuit.
Power delivered to the rotor across the airgap is equal to the mechanical power delivered to the load and the rotor cu loss.
Rotor power = mech., power + rotor cu loss

27. Rotor power = mech. Power + rotor cu loss
Pag = Pm + Pcu (1)
Pag = ωsT
and Pm = ωT
ω = ωs(1-S)
Pcu = S. ωs T (2)
SPag = slip power
Pm = (1-s) Pag (3)
Where, T & ωs – electromagnetic torque developed by the motor & synchronous angular velocity

28. The air gap flux of the m/c is established by the stator supply and it remains practically constant.
If stator impedance drop and supply voltage fluctuation are neglected.
Rotor cu loss is proposition to slip
The speed control of SRIM by connecting the external resistance in the rotor side.
Main drawback
Large slip power is dissipated in the resistance and
This reduces the efficiency of the motor at low speeds.

29. The speed of the SRIM can be controlled both in the
The slip power can be recovered to the supply source can be used to supply
An additional motor which is mechanically coupled to the main motor.
This type of drive is known as a slip power recovery system and
It improves the overall efficiency.
The speed of the SRIM can be controlled both in the
Sub synchronous region
Supper synchronous region

30. The slip power is taken from the rotor and feedback to the supply.
at this condition the motor operates in the sub synchronous region.
If electrical power is pumped to the rotor,
the motor operates in the super synchronous region
The torque equation, T = K2ΦI2 COSΦ2
T = K2 I2

31. When the motor operates at a constant i/p voltage
The flux remain constant & p.f is unity
The motor operates under constant T, rotor current(I2) is also constant
I2 = E2/Z2
where Z2 - rotor impedance
E2 - rotor emf

32. In the cascade connection,
E2 = KΦ(ωs – ω) + Eext
E2 – Eext = KΦ(ωs – ω)
where, ω – rotor speed
Eext – external emf fed to motor
The motor speed is dependent on the external emf Eext

33. If E2 – Eext is positive If E2 – Eext is negative
Power flows from the rotor to source of Eext and
The motor operates in sub-synchronous region
If E2 – Eext is negative
The power flows from source of Eext to the rotor and
The motor operates in the super synchronous region.

34. Types of slip power recovery system

35. It is classified into two types are,
Kramer system
Scherbius system
These two system can be further classified into two methods are,
Conventional method
Static method

36. Kramer system
It is only applicable for sub – synchronous speed operation.
The classification of Kramer system is,
Conventional Kramer system
Static Kramer system.

37. Conventional Kramer system

38. This system also called the electromecanacial cascade
The slip power is converted - dc power by a rotary converter and fed to the armature of a dc motor.
The speed of SRIM is adjusted by adjusting the speed of dc motor with the help of field regulator.
This system also called the electromecanacial cascade
Because the slip ring power is returned as mech., power to SRIM shaft by the dc motor.
If the mech., losses in cascade system are neglected the shaft power o/p of SRIM is,
Pm = (1 – S) Pin

39. Hence, it is also called the constant power cascade.
The slip power (Ps = Pin S) is added to Pm by converting it to mech., power by the dc motor.
This mech., power is fed to the SRIM shaft
The SRIM the power o/p remains constant
Hence, it is also called the constant power cascade.
This method is only used for large motor of 400KW or above.
Adv.,
Any speed, within the working range can be obtained.
Improves the power factor.

40. Modified Kramer system

42. Static Kramer system In rotor resistance control method,
The slip power is wasted
Instant of wasted the slip power is can be converted to 50 Hz AC and pumped back to the line
Here , the slip power can flow only in one direction.
This method of drive is called static Kramer drive.
The static Kramer drive offers speed control only for sub synchronous speed.
i.e., speed can control only less than the Ns speed.

43. Static Kramer system