1. Physics (14 - 16) Electrical Circuits Varying Resistance © SSER Ltd.

2. Current Electricity effectively travels at the speed of light in a conductor (186,000 miles/second) but slower in an insulating material. An electric current is a flow of charge carried by tiny particles known as electrons. Movement of charge is caused by the force from a voltage supply such as a battery or mains supply acting on electrons which are free to move. Note: The electrons flow in the opposite direction to that of the current.

3. Current An electric current is a flow of charge carried by tiny particles known as electrons. Movement of charge is caused by the force from a voltage supply such as a battery or mains supply acting on electrons which are free to move. Note: The electrons flow in the opposite direction to that of the current. Electricity effectively travels at the speed of light in a conductor (186,000 miles/second) but slower in an insulating material.

4. Electric current is measured in units called amps (A). The electric current is not used up by the components in a circuit but it transfers energy from the voltage source to the various components making up the circuit. Current Electric current is measured using an ammeter.

5. Electric current is measured in units called amps (A). The electric current is not used up by the components in a circuit but it transfers energy from the voltage source to the various components making up the circuit. Current Electric current is measured using an ammeter. The ammeter is placed in series within the circuit.

6. Voltage Potential difference is also measured in volts (V). The potential difference is a measure of the energy carried by the charge (current) flowing within the circuit. Voltage is supplied by a battery, cell or power supply and is measured in volts (V). The voltage of a power supply (converting other forms of energy into electrical) is an electromotive force (emf). The voltage across a circuit component, e.g. a bulb converting electrical energy into heat and light is a potential difference (p.d.).

7. Voltage Within an electrical circuit, the difference in electrical potentials across different components drops as each component converts electrical energy into other forms of energy. Potential difference is measured using a voltmeter. The voltmeter is placed in parallel to the circuit.

8. Voltage Within an electrical circuit, the difference in electrical potentials across different components drops as each component converts electrical energy into other forms of energy. Potential difference is measured using a voltmeter. The voltmeter is placed in parallel to the circuit. Note: the switch does not need to be closed to take a voltage reading across a battery.

9. Resistance Resistance is the property of a material which restricts the flow of electricity. Energy is converted into other forms (e.g. light, heat), as the voltage across the component drives the current through it. The unit of resistance is the Ohm (Ω). What causes resistance? As an electric current flows, charged particles called electrons move through a conductor. These moving electrons collide with the atoms of the conductor, making it more difficult for the current to flow. This causes the resistance. What factors affect resistance? Longer wires increases resistance. The electrons collide with atoms more often in a long wire than in a short wire. Thin wires increases resistance. A thin wire has fewer electrons to carry the current than a thick wire.

10. In 1826, based on his work on conduction in metal wires, Georg Ohm formulated a law relating to the current passing through a wire, and the potential difference (voltage) applied. Georg Simon Ohm (1789 - 1854) V = I x R This is known as Ohm’s Law. Ohm also introduced the SI unit of resistance, as the Ohm (Ω). He found that for a fixed temperature, the current flowing through a resistor is directly proportional to the potential difference across the resistor. Georg Ohm

11. Ohm’s Law Using Ohm’s Law, the resistance of any component can be calculated by measuring the current in the circuit, and the potential difference across the component.

12. Ohm’s Law Using Ohm’s Law, the resistance of any component can be calculated by measuring the current in the circuit, and the potential difference across the component.

13. A resistor is placed in a circuit with a potential differences of 12 volts and a current flow of 0.1A. R = V I R = 12V 0.1A R = 120Ω What is the resistance? The resistance is 120Ω Ohm’s Law Ohm’s Law also allows you, given any two values, to calculate any one of the other three values within the triangle.

14. A 10Ω resistor is placed in a circuit with a potential difference of 5 volts. I = V R I = 5V 10Ω I = 0.5A Ohm’s Law also allows you, given any two values, to calculate any one of the other three values within the triangle. What is the current? The current is 0.5A Ohm’s Law

15. A 20Ω resistor is placed in a circuit with a current of 0.1 A. V = I x R V = 0.1A x 20Ω V = 2V Ohm’s Law also allows you, given any two values, to calculate any one of the other three values within the triangle. What is the voltage across the resistor? The voltage is 2V

16. © SSER Ltd. To appreciate how a flow of electrons can carry an electric charge, a simple electric circuit can be compared with a domestic central heating system. Electron Flow in a Circuit

17. Ohm’s Law Drag each of these resistors into the circuit to find out how they affect the current flowing in the circuit. From the results you should see that: For a fixed potential difference within the circuit, the greater the resistance, the smaller the current.

18. . Current v Potential Difference Graphs Current against potential difference graphs can be used to show how the current varies through a given component, dependant upon the potential difference.

19. Thermistor The resistance of a thermistor is dependant upon the temperature. Turn up the temperature on the thermistor (drag the red slider on the thermometer) and see how it affects the resistance in the circuit. (If the current goes down, the resistance has gone up.) A thermistor’s resistance decreases as the temperature increases.

20. Light-dependant Resistor (LDR) Turn up the light on the LDR and see how it affects the resistance in the circuit. (If the current goes down, the resistance has gone up.) The LDR’s resistance decreases as the light intensity increases. The resistance of a light-dependant resistor (LDR) is dependant upon the levels of light.

21. End of Show Copyright © 2006 SSER Ltd. and its licensors. Images are for viewing purposes only. All rights reserved. Copyright © 2006 SSER Ltd. and its licensors. Images are for viewing purposes only. All rights reserved.