1. Sockets, Ratchets, and Impacts Speed Wrench - Available in 1/4”, 3/8”, 1/2” Drives

2. Ratchet - Available in 1/4”, 3/8”, 1/2” Drives Not a hammer or a punch!!

3. Socket Driver - Available in 1/4”, 3/8”, 1/2” Drives

4. Nut Driver -The socket part of the nut driver is made as part of the tool and cannot be changed

5. Breaker Bar - Does not ratchet - Has an extra long handle for more torque - Available in 1/4”, 3/8”, 1/2” Drives

6. Impact Driver Designed to loosen nuts and bolts with vibration - Available in 3/8”, 1/2” Drives

7. Cylinder Hone -

8. Extension - Available in 1/4”, 3/8”, 1/2” Drives - Available in 1” to 24” lengths

9. Hand tool socket - Hand tool sockets are chrome - Available in 1/4”, 3/8”, 1/2” Drives - Can be a 12pt. or 6pt. - Can be short wall or deep wall -Not to be used with impact tools

10. Impact sockets - Impact sockets have a black oxide finish - Available in 1/4”, 3/8”, 1/2” Drives - Can be a 12pt. or 6pt. - Can be short wall or deep wall - Can be used with hand tools

11. Sparkplug Socket - For removing and installing sparkplugs only - Has a protective rubber insert

12. Compression Tester -

13. Adjustable Wrench - Adjustable to the proper size - Most likely to round off corners - Fixed jaw towards the direction of force

14. Open End Wrench - Makes contact with only two sides - Can turn fasteners that you can’t get a socket on - Allows for faster turning

15. Box End Wrench - Ends of the wrench are boxed in or closed - Need to have access to one side of the bolt or nut - Less likely to slip or round off due to more contact - Can be 12pt or 6pt

16. Double offset - Allows you to reach a recessed fastener and still have some room for your knuckles

17. Combination Wrench - Open end has no offset - Box end has a 15 o offset - Available in 12pt or 6pt on box end

18. Allen or Hex Wrench - Six sided bar - Used for Cap bolts with a “Hex” recessed hole - Not interchangeable with a torx type fasteners

19. Wrenches  When using wrenches Always try to use the wrench so that you are pulling on the handle rather than pushing it.  Why?

20. Gear Puller -

21. Phillips Head Screwdriver

22. Flat Head Screwdriver

23. Flywheel Puller - Assists with the removal of the flywheel

24. Valve Spring Compressor -

25. Torx Bit - Not interchangeable with “Hex” wrenches - Can be a screwdriver type handle or a socket type - Can range in size from T5 to T40

26. Dead Blow Hammer - Has an empty cavity with lead shot - Plastic coated - Not for driving punches or chisels

27. Ballpeen Hammer - Used to drive punches and chisels - Not used for manipulating parts into place - Heavy steel or cast iron head

28. Ring Compressor -

29. Ring Expander -

30. Flywheel Holder -

31. Combination Slip-Joint Pliers - Used for hose clamps, holding parts, and griping materials - Not used to tighten or loosen fasteners

32. Channel Locks - Used for hose clamps, holding parts, and griping materials - Not used to tighten or loosen fasteners - Has an adjustable minimum opening jaw - Long handles for more gripping power

33. Needle Nose Pliers - Pointy jaws for reaching into small or tight areas - Some have a cutter for cutting small gauge wire, zip ties, etc. - Used for moving, holding, or manipulating objects - Not used to tighten or loosen fasteners

34. Vice-Grips - Used for clamping, holding, and Manipulating material and parts - Not for tightening or loosening fasteners

35. Side Cutters - Used for cutting wire, zip ties, small diameter materials - Not used to handle material or turn fasteners

36. Center Punch - Tapered shaft - Pointed end for marking material

37. Valve Lapper -

38. Gasket Scraper -

39. Torque Wrench -

40. Aligning Punch - Used for aligning parts - Flat end for driving - Longer tapered shaft

41. Pin Punch - Thin straight shaft for driving pins, bolts, other fasteners - Small ones are pin punches, Larger ones are Drift punches

42. Cold Chisel - Used for cutting or shearing material - Not used like a punch

43. Grind off the mushroom and form a chamfer Chisel and Punch Rules

44. Magnetic Pick-up Tool

45. Feeler Gauge

46. Spring Compressor