1. Quiz

2. QUESTION 1 The orbit tool allows you to … A.Move the whole screen up or down. B.Get a closer view. C.View all sides of an entity. D.View the inside of an entity.

3. QUESTION 2 The pan tool allows you to … A.Move the whole screen up or down, back and forth. B.Get a closer view. C.View all sides of an entity. D.Spin an entity.

4. QUESTION 3 The zoom tool allows you to … A.Move the whole screen up or down, back and forth. B.Get a closer view. C.View all sides of an entity. D.Spin an entity.

5. QUESTION 4 The axis lines are arranged… A.Red parallel to blue. B.Green parallel to red and blue. C.Blue perpendicular to red and green. D.In 45 degree angles.

6. QUESTION 5 To make an object into 3D… A.Use the 3D tool. B.Use the object tool. C.Use the push/pull tool. D.Use the move tool.

7. QUESTION 6 Inference is used to… A.Copy an entity. B.Erase an entity. C.Move an entity. D.Line up entities.

8. QUESTION 7 Endpoints on a line are… A.Red. B.Blue. C.Green. D.Cyan.

9. QUESTION 8 Mid points on a line or surface are… A.Red. B.Blue. C.Green. D.Cyan.

10. QUESTION 9 All other points on a line are… A.Red. B.Blue. C.Green. D.Cyan.

11. QUESTION 10 The push pull tool will not pull an entity if… A.It is already selected. B.It is not coplanar. C.It has already been pulled. D.The entity has been colored or textured with the paint bucket.

12. QUESTION 11 The best practice in drawing a line is: A.Click the line tool. Click and drag your mouse to the end of the line. B.Click the line tool. Click each endpoint of the line. C.Click the arrow tool. Click one end of the line, lift your finger, move your mouse to the end of the line and click again. D.Click the arrow tool. Click and drag a line.

13. QUESTION 12 The best practice in drawing a rectangle is: A.Click the rectangle tool. Click and drag your mouse around the rectangle. B.Click the line tool. Click each corner of the square. C.Click the rectangle tool. Click one corner of the rectangle, lift your finger, move your mouse to the opposite corner diagonally, and click again. D.Click the rectangle tool. Click and drag a rectangle.

14. QUESTION 13 The best practice in push/pull is: A.Push or pull the edge of the entity. B.Always push pull from the bottom. C.Push or pull from any part of the top surface. D. Be sure the arrow of the push/pull tool is centered on the top surface of the entity you want to push or pull.

15. QUESTION 14 To heal a surface is … A.To color it with the paint bucket. B.To draw the lines to complete the edge. C.Erase the lines on the edge of the surface. D.Smooth it.

16. QUESTION 15 A surface is coplanar if… A.It has been colored with the paint bucket. B.All sides are in the same plane. C.Each side aligns with a different axis. D.It cannot be pulled into 3D.

17. QUESTION 16 Bounding edges can be found on… A.All Surfaces. B.All tools. C.All axis. D.All lines.

18. QUESTION 17 Polygons can be drawn with … A.The polygon tool only. B.The rectangle tool. C.The polygon or circle tool. D.The circle tool only.

19. QUESTION 18 5 sided Polygons can be drawn by … A.Typing 5’ and pressing enter. B.Typing 5” and pressing enter. C.Typing 5p and pressing enter. D.Typing 5s and pressing enter.

20. QUESTION 19 To pull a surface up five feet… A.Typing 5’ and pressing enter. B.Typing 5” and pressing enter. C.Typing 5p and pressing enter. D.Typing 5s and pressing enter.

21. QUESTION 20 An 8 sided 3D polygon drawn with the polygon tool has… A.A smooth cylindrical side. B.8 rectangular sides. C.A circular top. D.8 bounding edges.

22. QUESTION 21 An 8 sided 3D polygon drawn with the circle tool has… A.A smooth cylindrical side. B.8 rectangular sides. C.A polygonal top. D.8 bounding edges.

23. QUESTION 22 Circles are by default… A.8 sides. B.12 sides. C.36 sides. D.24 sides.

24. QUESTION 23 Arcs are by default… A.8 sides. B.12 sides. C.36 sides. D.24 sides.

25. QUESTION 24 Infer to, or find, the center of a circle by hovering over… A.The center. B.The edge. C.The surface. D.The circle tool.

26. QUESTION 25 To stop an action or a tool… A.Press the enter key. B.Press the escape key. C.Press the space bar. D.Press delete.

27. QUESTION 26 Using the push/pull tool to cut away part of an entity does not work if… A.The sides of the entity are not parallel. B.The entity is too tall. C.The entity has been painted. D.The surface you are pushing is a circle or arc.

28. QUESTION 27 Using the push/pull tool to cut away part of an entity does not work if… A.The sides of the entity are parallel. B.The entity is too tall. C.There is an obstruction line or edge in the way. D.The surface you are pushing is a circle or arc.

29. QUESTION 28 Using the follow me tool requires… A.Parallel sides. B.A 3D entity and a line. C.A surface and an arc. D.A path and a shape.

30. QUESTION 30 To make an entity larger use… A.The rotate tool. B.The scale tool. C.Copy, paste. D.The offset tool.

31. QUESTION 30 To frame a door or window use… A.The rotate tool. B.The scale tool. C.Copy, paste. D.The offset tool.

32. QUESTION 31 To turn an object use… A.The rotate tool. B.The scale tool. C.Copy, paste. D.The offset tool.

33. QUESTION 32 To copy an object use… A.The rotate tool. B.The scale tool. C.Copy, paste. D.The offset tool.

34. QUESTION 33 An entity made up of smaller entities is called… A.A scale. B.An ungrouped entity. C.A component. D.A coplanar entity.

35. QUESTION 34 Reverse the direction of an entity using … A.A component. B.The Follow me tool. C.The scale tool. D.The offset tool.

36. QUESTION 34 To make a sphere use … A.A component. B.The Follow me tool. C.The scale tool. D.The offset tool.