1. Network+ Guide to Networks 5 th Edition Chapter 6 Network Hardware

2. Network+ Guide to Networks, 5 th Edition2 Objectives Identify the functions of LAN connectivity hardware Install, configure, and differentiate between network devices such as, NICs, hubs, bridges, switches, routers, and gateways Explain the advanced features of a switch and understand popular switching techniques, including VLAN management Explain the purposes and properties of routing Describe common IPv4 and IPv6 routing protocols

3. Network+ Guide to Networks, 5 th Edition3 NICs (Network Interface Cards) Connectivity devices –Enable device transmission –Transceiver Transmits and receives data Physical layer and Data Link layer functions –Issue data signals –Assemble and disassemble data frames –Interpret physical addressing information –Determine right to transmit data

4. Network+ Guide to Networks, 5 th Edition4 NICs (cont’d.) Smart hardware –Perform prioritization –Network management –Buffering –Traffic-filtering Do not analyze information –Added by Layers 3 through 7 OSI model protocols Importance –Common to every networking device, network

5. Network+ Guide to Networks, 5 th Edition5 Types of NICs Before ordering or installing NIC –Know device interface type NIC dependencies –Access method –Network transmission speed –Connector interfaces –Compatible motherboard or device type –Manufacturer

6. Network+ Guide to Networks, 5 th Edition6 Types of NICs (cont’d.) Bus –Circuit, signaling pathway –Motherboard uses to transmit data to computer’s components Memory, processor, hard disk, NIC –Differ according to capacity Defined by data path width and clock speed –Data path size Parallel bits transmitting at any given time Proportional to attached device’s speed

7. Network+ Guide to Networks, 5 th Edition7 Internal Bus Standards Expansion slots –Multiple electrical contacts on motherboard –Allows bus expansion Expansion card (expansion board) –Circuit board for additional devices –Inserts into expansion slot, establishes electrical connection –Device connects to computer’s main circuit or bus –Computer centrally controls device

8. Network+ Guide to Networks, 5 th Edition8 Internal Bus Standards (cont’d.) Multiple bus types –PCI bus: most popular expansion board NIC PCI (Peripheral Component Interconnect) –32- or 64-bit bus –Clock speeds rated at 33-, 66- or 133-MHz –Maximum data transfer rate: 1 Gbps –Introduced by Intel (1992) –Latest official version: 3.0 (2004)

9. Network+ Guide to Networks, 5 th Edition9 ISA (Industry Standard Architecture) –Original PC bus type (early 1980s) Support for 8-bit and 16-bit data path, 4.77-MHz clock PCI bus characteristics –Shorter connector length, faster data transmission Compared to previous bus types (ISA) –PCs and Macintosh compatible Figure 6-1 PCI NIC

10. Network+ Guide to Networks, 5 th Edition10 PCIe (PCI Express) –32- or 64-bit bus –Maximum 133-MHz clock speed –Transfer rate 500 Mbps per data path (full-duplex transmission) Figure 6-2 PCIe NIC

11. Network+ Guide to Networks, 5 th Edition11 Internal Bus Standards (cont’d.) PCIe advantages over PCI –More efficient data transfer –Quality of service distinctions support –Error reporting, handling –Current PCI software compatible PCIe slots differ from conventional PCI –Vary by lanes supported –Lane offers full-duplex throughput of 500 Mbps Support up to 16 lanes x16 slot : 8 Gbps throughput

12. Network+ Guide to Networks, 5 th Edition12 Determining bus type –Read documentation –Look inside PC case –If more than one expansion slot type: Refer to NIC, PC manufacturers’ guidelines Choose NIC matching most modern bus Figure 6-3 A motherboard with multiple expansion slots

13. Network+ Guide to Networks, 5 th Edition13 Peripheral Bus Standards Attach peripheral devices externally External connection advantage –Simple installation Personal Computer Memory Card International Association or PCMCIA –Sets standards for externally attached cards Connect virtually any external device type PC Card –First standard PCMCIA-standard adapter 16- bit interface running at 8 MHz

14. Network+ Guide to Networks, 5 th Edition14 CardBus standard (1990s) –32-bit interface running at 33 MHz –Matches PCI expansion board standard Figure 6-4 A CardBus NIC

15. Network+ Guide to Networks, 5 th Edition15 Peripheral Bus Standards (cont’d.) ExpressCard standard –Many different external devices connect to portable computers –26-pin interface –Data transfer rates: 250 Mbps in each direction 500 Mbps total –Same data transfer standards as PCIe specification –Two sizes 34 mm, 54 mm wide

16. Network+ Guide to Networks, 5 th Edition16 Peripheral Bus Standards (cont’d.) Figure 6-5 ExpressCard modules

17. Network+ Guide to Networks, 5 th Edition17 Peripheral Bus Standards (cont’d.) USB (universal serial bus) port –Two USB standards Difference: speed USB 1.1: transfer rate of 12 Mbps USB 2.0: transfer rate of 480 Mbps –Future USB 3.0 (SuperSpeed USB) Transfer rate: 4.8 Gbps

18. Network+ Guide to Networks, 5 th Edition18 Types of NICs (cont’d.) Figure 6-6 A USB NIC

19. Network+ Guide to Networks, 5 th Edition19 Peripheral Bus Standards (cont’d.) Firewire –Apple Computer (1980s) –IEEE 1394 standard (1995) –Traditional Firewire connection: 400 Mbps (max) –Newer version: 3 Gbps –Connects most peripheral types –Connects small network Two or more computers using bus topology

20. Network+ Guide to Networks, 5 th Edition20 Peripheral Bus Standards (cont’d.) FireWire-connected peripherals –Similar to USB- and PCMCIA-connected peripherals Simple installation Supported by most modern operating systems –Two connector varieties: 4-pin and 6-pin –6-pin connector Two pins supply power Interconnect computers

21. Network+ Guide to Networks, 5 th Edition21 Peripheral Bus Standards (cont’d.) Figure 6-7 FireWire connectors (4-pin and 6-pin)

22. Network+ Guide to Networks, 5 th Edition22 Peripheral Bus Standards (cont’d.) CompactFlash –Designed by CompactFlash Association (CFA) Ultrasmall Removable data and input/output device –Latest standard: 4.0 Data transfer rate: 133 Mbps –Uses Connects devices too small for PCMCIA slots Wireless connections

23. Network+ Guide to Networks, 5 th Edition23 Peripheral Bus Standards (cont’d.) Figure 6-8 A CompactFlash NIC

24. Network+ Guide to Networks, 5 th Edition24 On-Board NICs Connect device directly to motherboard –On-board ports: mouse, keyboard New computers, laptops –Use onboard NICs integrated into motherboard Advantages –Saves space –Frees expansion slots

25. Network+ Guide to Networks, 5 th Edition25 Contain antennas –Send, receive signals –All bus types supported Disadvantages over wire-bound NICs –More expensive –Bandwidth and security limitations Figure 6-9 Wireless NICs Wireless NICs

26. Installing NICs Three general steps –Install hardware –Install NIC software –Configure firmware (if necessary) Set of data, instructions Saved to NIC’s ROM (read-only memory) chip Use configuration utility program EEPROM (electrically erasable programmable read- only memory) –Apply electrical charges ROM data erased, changed Network+ Guide to Networks, 5th Edition26

27. Network+ Guide to Networks, 5 th Edition27 Installing and Configuring NIC Hardware Read manufacturer’s documentation Install expansion card NIC –Verify toolkit contents –Unplug computer –Ground yourself –Open computer case Select slot, insert NIC, attach bracket, verify cables –Replace cover, turn on computer Configure NIC software

28. Network+ Guide to Networks, 5 th Edition28 Figure 6-10 A properly inserted NIC

29. Physically install PCMCIA-standard NIC –Insert card into PCMCIA slot Network+ Guide to Networks, 5th Edition29 Figure 6-11 Installing a PCMCIA-standard NIC Installing and Configuring NIC Hardware (cont’d.)

30. Network+ Guide to Networks, 5 th Edition30 Installing and Configuring NIC Hardware (cont’d.) Modern operating systems –Do not require restart for PCMCIA-standard adapter Servers, other high-powered computers –Install multiple NICs –Repeat installation process for additional NIC –Choose different slot

31. Network+ Guide to Networks, 5 th Edition31 Installing and Configuring NIC Software Device driver –Software Enables attached device to communicate with operating system Purchased computer –Drivers installed Add hardware to computer –Must install drivers

32. Network+ Guide to Networks, 5 th Edition32 Installing and Configuring NIC Software (cont’d.) Operating system built-in drivers –Automatically recognize hardware, install drivers –Computer startup Device drivers loaded into RAM Computer can communicate with devices Drivers not available from operating system –Install and configure NIC software Use operating system interface

33. Network+ Guide to Networks, 5 th Edition33 Figure 6-12 Windows Vista Update Driver Software dialog box

34. Network+ Guide to Networks, 5 th Edition34 Interpreting LED Indicators After NIC is installed: –Test by transmitting data –Assess NIC LEDs for network communication Vary by manufacturer Read documentation –Common lights ACT, LNK, LED, TX, RX

35. Network+ Guide to Networks, 5 th Edition35 IRQ (Interrupt Request) Message to computer –Stop and pay attention to something else Interrupt –Circuit board wire Device issues voltage to signal request IRQ number –Uniquely identifies component to main bus –NICs use IRQ 9, 10, or 11

36. Network+ Guide to Networks, 5 th Edition36 Table 6-1 IRQ assignments

37. Network+ Guide to Networks, 5 th Edition37 IRQ (Interrupt Request) (cont’d.) Two devices using same interrupt –Resource conflicts, performance problems Many symptoms –Must reassign IRQ Through operating system Through adapter’s EEPROM configuration utility Through computer’s CMOS configuration utility

38. Network+ Guide to Networks, 5 th Edition38 IRQ (Interrupt Request) (cont’d.) CMOS (complementary metal oxide semiconductor) –Microchip requiring very little energy to operate –Stores settings pertaining to computer’s devices –Battery powered Settings saved after computer turned off –Information used by BIOS (basic input/output system) BIOS –Simple instruction set Enables computer to initially recognize hardware

39. Network+ Guide to Networks, 5 th Edition39 Memory Range Memory NIC, CPU use for exchanging, buffering data Some are reserved for specific devices NICS –High memory area (A0000–FFFFF range) –Manufacturers prefer certain ranges Resource conflicts less likely (than IRQ settings)

40. Network+ Guide to Networks, 5 th Edition40 Base I/O Port Memory area –Channel for moving data between NIC and CPU Cannot be used by other devices NICs use two channel memory ranges –Base I/O port settings identify beginning of each range

41. Network+ Guide to Networks, 5 th Edition41 Firmware Settings Contain NIC’s transmission characteristics Combination –EEPROM chip on NIC and data it holds Change firmware –Change EEPROM chip –Requires bootable CD-ROM Configuration, install utility shipped with NIC

42. Network+ Guide to Networks, 5 th Edition42 Firmware Settings (cont’d.) Configuration utility –View IRQ, I/O port, base memory, node address –Change settings –Perform diagnostics NIC’s physical components, connectivity Loopback plug (loopback adapter) –Outgoing signals redirected into computer for testing –Use with loopback test

43. Network+ Guide to Networks, 5 th Edition43 Choosing the Right NIC Considerations –Compatibility with existing system Network bus type, access method, connector types, transmission speed –Drivers available Operating system, hardware –Subtle differences Affecting network performance Important for server

44. Network+ Guide to Networks, 5 th Edition44 Table 6-2 NIC characteristics

45. Repeaters and Hubs Repeater –Simplest connectivity device regenerating signals –Operates at Physical layer Has no means to interpret data –Limited scope One input port, one output port Receives and repeats single data stream –Suitable for bus topology networks –Extend network inexpensively –Rarely used on modern networks Limitations; other devices decreasing costs Network+ Guide to Networks, 5th Edition45

46. Network+ Guide to Networks, 5 th Edition46 Repeaters and Hubs (cont’d.) Hub –Repeater with more than one output port Multiple data ports, uplink port –Repeats signal in broadcast fashion –Operates at Physical layer –Ethernet network hub Star or star-based hybrid central connection point –Connect workstations, print servers, switches, file servers, other devices

47. Network+ Guide to Networks, 5 th Edition47 Repeaters and Hubs (cont’d) Hub (cont’d.) –Devices share same bandwidth amount, collision domain More nodes leads to transmission errors, slow performance –Placement in network varies Simplest: stand-alone workgroup hub Different hub to each small workgroup Placement must adhering to maximum segment and length limitations

48. Network+ Guide to Networks, 5 th Edition48 Repeaters and Hubs (cont’d) Figure 6-13 Hubs in a network design

49. Network+ Guide to Networks, 5 th Edition49 Hub (cont’d.) –Hubs vary according to: Supported media type, data transmission speeds –Passive hubs, Intelligent hubs (managed hubs), Stand-alone hubs (workgroup hubs) –Replaced by switches routers Limited features Merely repeat signals Figure 6-14 A stand-alone hub

50. Network+ Guide to Networks, 5 th Edition50 Bridges Connects two network segments –Analyze incoming frames and decide where to send Based on frame’s MAC address Operate at Data Link layer Single input port and single output port Interpret physical addressing information Advantages over repeaters and hubs –Protocol independence –Add length beyond maximum segments limits –Improve network performance

51. Network+ Guide to Networks, 5 th Edition51 Disadvantage compared to repeaters and hubs –Longer to transmit data Filtering database (forwarding table) –Used in decision making Filter or forward Figure 6-15 A bridge’s use of a filtering database

52. Network+ Guide to Networks, 5 th Edition52 Bridges (cont’d.) New bridge installation –Learn network –Discover destination packet addresses –Record in filtering database Destination node’s MAC address Associated port –All network nodes discovered over time Today bridges nearly extinct –Improved router and switch speed, functionality –Lowered router and switch cost

53. Network+ Guide to Networks, 5 th Edition53 Switches Subdivide network –Smaller logical pieces, segments Operates at Data Link layer (traditional) Operate at layers 3 and 4 (advanced) Interpret MAC address information Components –Internal processor, operating system, memory, several ports

54. Network+ Guide to Networks, 5 th Edition54 Multiport switch advantages over bridge –Better bandwidth use, more cost-efficient –Each port acts like a bridge Each device effectively receives own dedicated channel –Ethernet perspective Dedicated channel represents collision domain Figure 6-16 Switches

55. Network+ Guide to Networks, 5 th Edition55 Switches (cont’d.) Historically –Switches replaced hubs, eased congestion, provided better security, performance Disadvantages –Can become overwhelmed despite buffers Cannot prevent data loss UDP collisions mount: network traffic halts Switches replaced workgroup hubs –Decreased cost, easy installation, configuration, –Separate traffic according to port

56. Network+ Guide to Networks, 5 th Edition56 Installing a Switch Follow manufacturer’s guidelines General steps (assume Cat 5 or better UTP) –Verify switch placement –Turn on switch –Verify lights, self power tests –Configure (if necessary) –Connect NIC to a switch port (repeat for all nodes) –After all nodes connected, turn on nodes –Connect switch to larger network (optional)

57. Network+ Guide to Networks, 5 th Edition57 Installing a Switch (cont’d.) Figure 6-17 Connecting a workstation to a switch Figure 6-18 A switch on a small network

58. Network+ Guide to Networks, 5 th Edition58 Switching Methods Difference in switches –Incoming frames interpretation –Frame forwarding decisions making Four switching modes exist –Two basic methods discussed Cut-Through Mode Store-and-Forward Mode

59. Network+ Guide to Networks, 5 th Edition59 Cut-Through Mode Switch reads frame’s header Forwarding decision made before receiving entire packet –Uses frame header: first 14 bytes contains destination MAC address Cannot verify data integrity using frame check sequence Can detect runts –Erroneously shortened packets Runt detected: wait for integrity check

60. Network+ Guide to Networks, 5 th Edition60 Cut-Through Mode (cont’d.) Cannot detect corrupt packets –May propagate flawed packets Advantage –Speed Disadvantage –Data buffering (switch flooded with traffic) Best use –Small workgroups needing speed –Low number of devices

61. Network+ Guide to Networks, 5 th Edition61 Store-and-Forward Mode Switch reads entire data frame into memory –Checks for accuracy before transmitting information Advantage over cut-through mode –Transmit data more accurately Disadvantage over cut-through mode –More time consuming Best use –Larger LAN environments; mixed environments –Can transfer data between segments running different transmission speeds

62. Network+ Guide to Networks, 5 th Edition62 VLANs and Trunking VLANs (virtual local area networks) –Logically separate networks within networks Groups ports into broadcast domain Broadcast domain (subnet) –Port combination making a Layer 2 segment Ports rely on layer 2 device to forward broadcast frames Collision domain –Ports in same broadcast domain Do not share single channel

63. Network+ Guide to Networks, 5 th Edition63 VLANs and Trunking (cont’d.) Figure 6-19 A simple VLAN design

64. Network+ Guide to Networks, 5 th Edition64 VLANs and Trunking (cont’d.) Advantage of VLANs –Flexible Ports from multiple switches or segments Use any end node type –Reasons for using VLAN Separating user groups Isolating connections Identifying priority device groups Grouping legacy protocol devices

65. VLANs and Trunking (cont’d.) VLAN creation –Configuring switch software Manually through configuration utility Automatically using VLAN software tool –Critical step Indicate to which VLAN each port belongs –Additional specifications Security parameters, filtering instructions, port performance requirements, network addressing and management options Maintain VLAN by switch software Network+ Guide to Networks, 5th Edition65

66. Network+ Guide to Networks, 5 th Edition66 Figure 6-20 Result of the show vlans command on a Cisco switch

67. Network+ Guide to Networks, 5 th Edition67 VLANs and Trunking (cont’d.) Potential VLAN issues –Cutting off group from rest of network Correct by using router Trunking –Switch’s interface carries traffic of multiple VLANs Trunk –Single physical connection between devices Many logical VLANs transmit, receive data VLAN data separation –Frame contains VLAN identifier in header

68. Network+ Guide to Networks, 5 th Edition68 VLANs and Trunking (cont’d.) Advantage of VLAN trunking –Economical interface usage –Switches make efficient use of processing capabilities VLAN configuration –Can be complex –Requires careful planning Ensure users and devices can exchange data Ensure VLAN switch properly interacts with other devices

69. Network+ Guide to Networks, 5 th Edition69 STP (Spanning Tree Protocol) IEEE standard 802.1D Operates in Data Link layer Prevents traffic loops –Calculating paths avoiding potential loops –Artificially blocking links completing loop Three steps –Select root bridge based on Bridge ID –Examine possible paths between network bridge and root bridge –Disables links not part of shortest path

70. Network+ Guide to Networks, 5 th Edition70 STP (cont’d.) Figure 6-21 Enterprise-wide switched network

71. Network+ Guide to Networks, 5 th Edition71 STP (cont’d.) Figure 6-22 STP-selected paths on a switched network

72. STP (cont’d.) History –Introduced in 1980s Original STP too slow –RSTP (Rapid Spanning Tree Protocol) Newer version IEEE’s 802.1w standard Cisco and Extreme Networks –Proprietary versions No enabling or configuration needed –Included in switch operating software May alter default priorities Network+ Guide to Networks, 5th Edition72

73. Network+ Guide to Networks, 5 th Edition73 Content and Multilayer Switches Layer 3 switch (routing switch) –Interprets Layer 3 data Layer 4 switch –Interprets Layer 4 data Content switch (application switch) –Interprets Layer 4 through Layer 7 data Advantages –Advanced filtering, statistics keeping, security functions

74. Network+ Guide to Networks, 5 th Edition74 Content and Multilayer Switches (cont’d.) Disadvantages –No agreed upon standard Layer 3 and Layer 4 switch features vary widely Distinguishing between Layer 3 and Layer 4 switch –Manufacturer dependent Higher-layer switches –Three times Layer 2 switches –Used in backbone

75. Network+ Guide to Networks, 5 th Edition75 Routers Multiport connectivity device –Directs data between network nodes –Integrates LANs and WANs Different transmission speeds, protocols Operate at Network layer (Layer 3) –Directs data from one segment or network to another –Logical addressing –Protocol dependent Slower than switches and bridges –Need to interpret Layers 3 and higher information

76. Network+ Guide to Networks, 5 th Edition76 Routers (cont’d.) Traditional stand-alone LAN routers –Being replaced by Layer 3 routing switches New niche –Specialized applications Linking large Internet nodes Completing digitized telephone calls

77. Network+ Guide to Networks, 5 th Edition77 Router Characteristics and Functions Intelligence –Tracks node location –Determine shortest, fastest path between two nodes –Connects dissimilar network types Large LANs and WANs –Routers indispensible Router components –Internal processor, operating system, memory, input and output jacks, management control interface

78. Network+ Guide to Networks, 5 th Edition78 Modular router –Multiple slots Holding different interface cards, other devices Inexpensive routers –Home, small office use Figure 6-23 Routers

79. Router Characteristics and Functions (cont’d.) Router tasks –Connect dissimilar networks –Interpret Layer 3 addressing –Determine best data path –Reroute traffic Optional functions –Filter broadcast transmissions –Enable custom segregation, security –Support simultaneous connectivity –Provide fault tolerance –Monitor network traffic, diagnose problems Network+ Guide to Networks, 5th Edition79

80. Network+ Guide to Networks, 5 th Edition80 Router Characteristics and Functions (cont’d.) Directing network data –Static routing Administrator programs specific paths between nodes –Dynamic routing Router automatically calculates best path between two nodes Routing table Installation –Simple: small office, home LANs –Challenging: sizeable networks

81. Network+ Guide to Networks, 5 th Edition81 Router Characteristics and Functions (cont’d.) Figure 6-24 The placement of routers on a LAN

82. Network+ Guide to Networks, 5 th Edition82 Routing Protocols Best path –Most efficient route from one node to another –Dependent on: Hops between nodes Current network activity Unavailable link Network transmission speed Topology –Determined by routing protocol

83. Routing Protocols (cont’d.) Routing protocol –Router communication –Collects current network status data Contribute to best path selection Routing table creation Router convergence time –Time router takes to recognize best path Change or network outage event –Distinguishing feature Overhead; burden on network to support routing protocol Network+ Guide to Networks, 5th Edition83

84. Network+ Guide to Networks, 5 th Edition84 Distance-Vector: RIP, RIPv2, BGP Distance-vector routing protocols –Determine best route based on distance to destination –Factors Hops, latency, network traffic conditions RIP (Routing Information Protocol) –Only factors in number of hops between nodes Limits 15 hops –Interior routing protocol –Slow and less secure

85. Network+ Guide to Networks, 5 th Edition85 Distance-Vector: RIP, RIPv2, BGP (cont’d.) RIPv2 (Routing Information Protocol Version 2) –Generates less broadcast traffic, more secure –Cannot exceed 15 hops –Less commonly used BGP (Border Gateway Protocol) –Communicates using BGP-specific messages –Many factors determine best paths –Configurable to follow policies –Most complex (choice for Internet traffic)

86. Network+ Guide to Networks, 5 th Edition86 Link-State: OSPF, IS-IS Link-state routing protocol –Routers share information Each router independently maps network, determines best path OSPF (Open Shortest Path First) –Interior or border router use –No hop limit –Complex algorithm for determining best paths –Each OSPF router Maintains database containing other routers’ links

87. Network+ Guide to Networks, 5 th Edition87 Link-State: OSPF, IS-IS (cont’d.) IS-IS (Intermediate System to Intermediate System) –Codified by ISO –Interior routers only –Supports two Layer 3 protocols IP ISO-specific protocol –Less common than OSPF

88. Hybrid: EIGRP Hybrid –Link-state and distance-vector characteristics –EIGRP (Enhanced Interior Gateway Routing Protocol) Most popular Cisco network routers only –EIGRP benefits Fast convergence time, low network overhead Easier to configure and less CPU-intensive than OSPF Supports multiple protocols Accommodates very large, heterogeneous networks Network+ Guide to Networks, 5th Edition88

89. Gateways and Other Multifunction Devices Gateway –Combinations of networking hardware and software Connecting two dissimilar networks –Connect two systems using different formatting, communications protocols, architecture –Repackages information –Reside on servers, microcomputers, connectivity devices, mainframes Popular gateways –E-mail gateway, Internet gateway, LAN gateway, Voice/data gateway, Firewall Network+ Guide to Networks, 5th Edition89

90. Summary NIC interface cards –Types, installation, testing, IRQ use, Base I/O port use, firmware settings, selection Repeater and hubs Bridges Switches –Installation, switching methods, VLANs and trunking, STP (Spanning Tree Protocol), Content and Multilayer Switches Router characteristics and functions, protocols Gateways and other multifunction devices Network+ Guide to Networks, 5th Edition90