1. GS3055-I Installation Process

2. GS3055-I Overview The GS3055-I is:
A universal wireless alarm communicator that can be used in a backup or primary role.
A device which connects the alarm control panel to the GSM network and reports alarm signals directly to a monitoring central station receiver (Sur-Gard System III/ System II).
A digital transmitter which provides full reporting from any control panel that communicates using Contact ID format.

3. GS3055-I Service Provider What is CONNECT 24?
CONNECT 24 is the GS3055-I service provider
CONNECT 24 provides the automated telephone activation system for the activation of GS3055-I units (GVRU, Voice Response Unit)
CONNECT 24 provides web-user interface support for the programming of GS3055-I units
CONNECT 24 provides account administration, billing and rate plans to GS3055-I customers

4. GS3055-I Enrolment Steps
In order to properly enrol a GS3055-I unit you must follow these steps :
STEP 1 – Activate your SIM card with Connect 24*
STEP 2 – Initialize the GS3055-I with Connect 24
STEP 3 – Determine best signal strength location
STEP 4 - Connect the GS3055-I to the control panel
STEP 5 - Program the control panel to use Contact ID format
STEP 6 – Test the GS3055-I
Note: GS3055-I unit must be powered down for STEPS 1 and 2

5. GS3055-I SIM Card Activation (GVRU)
SIM Card Activations must be activated with Connect 24 prior to use. Please call the VRU at least 24 hours prior to installation. To activate a SIM Card, you will need the following information:
Installer’s ID Number: It identifies each installer listed on the Dealer Enrolment Form
Installer’s PIN Number: It identifies each installer with a 4 digit PIN number
The SIM Card Number: (Subscriber Identity Module), digits located on SIM Card
Note: Only authorized dealers can activate a SIM Card with CONNECT 24

6. GS3055-I Initialization (GVRU)
To initialize a GS3055-I unit, you will need the following information:
Profile Number: It represents the Central Station Receiver IP address and Rate Plan
Installer’s ID Number: It identifies each installer listed on the Dealer Enrolment Form
Installer’s PIN Number: it identifies each installer with a 4 digit PIN number
The Central Station Account Number: Account number to be transmitted to the Central Station Receiver
The SIM Card Number: (Subscriber Identity Module), digits located on SIM Card
The DNIS Number: (Dialled Number Information Service), Check your work order
Test transmission selection: daily, weekly or monthly
Determine if GS3055-I unit is the primary or backup communicator
Determine the type of installation Residential or Commercial
Note: Only authorized dealers can initialize a GS3055-I with CONNECT 24

7. GS3055-I Signal Strength Test
To test the signal strength of a GS3055-I, you need:
The antenna must be connected to the GS3055-I
The SIM Card must be inserted into the GS3055-I
The Battery must be connected to the GS3055-I
The Signal Strength levels on GS3055-I are:
Excellent Signal Strength = GREEN LEDS 3 and 4
Good Signal Strength = GREEN LED 4
Poor Signal Strength = GREEN LED 4 (Flashing)
No signal Strength = OFF
For a proper installation, the GS3055-I must have
a Good Signal Strength

8. GS3055-I – Telephone Wiring (Back-up Mode)
To Power Supply
From RJ-31X Demarcation
To Premise Telephones

9. GS3055-I Control Panel Programming
Panel programming consist of:
Program any phone number (at least 1 digit)
Program the corresponding account number
Program the panel’s format as Contact ID
Program Reporting codes or activate automatic reporting option
Enable the phone line communicator

10. GS3055-I Testing To test a GS3055-I unit, follow the next steps:
Disconnect the telephone line from the TIP and RING terminals on the GS3055-I unit
Verify that LED 2 (YELLOW) is ON. This indicates that the unit is in GSM mode
Connect a voltmeter to R1 and T1 on the GS3055-I unit, the voltage reading should be around 34.5Vdc (dial tone)
Arm the control panel and violate a zone, so that the panel attempts to report the event
Connect a butset to RING and TIP on the control panel to verify that the control panel is communicating

11. GS3055-I – Testing
To Power Supply
To Premise Telephones

12. GS3055-I
Questions?