1. INAlA TECHNOLOGIEs Installation Training:
ECS (Equipment Communications System) ECS-L Commissioning
Version 1.0

2. Commissioning: ECS-L Procedure
ECS-L Commissioning
Commissioning: ECS-L Procedure

3. ECS-L - commissioning SAM Training Setting up of the unit:
Power unit on
Connect using the ITMS ECT
Set-up the communication ports for the devices you are connecting to it
Set-up the Sever IP address and APN - Customer Dependent
Click on set after making a change to save the configuration to the unit.
Check that LED is flashing accordingly to indicate that it is logged onto the network and APN - Customer Dependent .
Call to commission site with representative.
ECS-L Communication Cable:
A “Straight RS232” cable must be used between the ECS-L and the computer. (DB9 to IDC 10Way)
Once Connected open the “ITMS-C ECT” software.
Input User Name and Password, select “Serial Communication) and Click on Login
Port Settings
SAM1.5 = Physical port 2 – Virtual Port 310, Baud rate
L&G = Physical port 4 – Virtual Port 309, Baud rate 19200
SAM2 & Access Control = Physical port 1 – Virtual Port 301, Baud rate 9600
Red and Green LED
Red and Green Flashing = Modem is on and searching for network
Red LED on = GSM Network found
Green LED on = Modem logged onto APN
Green LED on and Red intermittent = Communication to Server
*Note – Check following slide for detail information of above procedure
SAM Training

4. ECS-L – Physical Port Numbers
* The physical port that is connected to the SAM must be selected as the “Event PORT”
PORT 4 - RS485
PORT 3 - RS232
PORT 2 - RS232
PORT 1 - RS485
PORT 5 - RS232 (ECT)
PORT 3 - RS232
PORT 5 - RS232 (ECT)
PORT 4 - RS485
PORT 2 - RS232
PORT 1 – RS485
GND
+12vdc
SAM Training

5. Software for ECS-L (Equipment Communication Controller-light)
Communication Controller Software (ECT):
Current Version ECT – V2.28
ECT Version is viewed on the top left corner as indicated with the yellow circle
EG: “ITMS-C Ver 2.28”
Current Version Firmware – V2026
Firmware Version is viewed on the button left corner as indicated with the Red circle
EG: “S/W: ”
IP address is automatically allocated to sim card and is displayed.
Input APN name and Server IP for applicable operator - Customer Dependent
SAM Training

6. Equipment Communication Controller – Port & server allocations
Virtual Port Allocations
301
SAM2 or SAM3 and Access Control
302
Rectifier A
303
Rectifier B
304
Generator
305
AVR
306
BMON
307
Fuel Cell 1
308
Fuel Cell 2
309
Energy Meter / Fire System
310
SAM 1.5 REC
Vodacom Server Name
Vodacom UDP Server IP
UDP Server Port
ZABLV CEN
299
ZABLV EAS
ZABLV LIM
ZABLV MPU
ZABLV SGC
ZABLV SGS
ZABLV WES
NGA Existing Server
Telkom Server Name
Telkom UDP Server IP
UDP Server Port
2999
Operator Name
APN Name
Vodacom
Vodameter
Neotel
internet
Neotel Server Name
Neotel UDP Server IP
UDP Server Port
299
SAM Training

7. Equipment Communication Controller – Coms wiring
Communication Cable Consumables
ECS (Eth/E1), ECS-L
1. 10 way Ribbon Cable
2. 10 way IDC connector for 10 way ribbon cable
3. DB9 IDC, male and female for 10 way ribbon cable
ECS (Eth/GPRS), ECS (Eth/E1) & ECS-L
1. DB9, male and female, solder type
2. Milar cable used with point 1 above (Same as SAM2 Coms cross over cable)
1. RJ9 – small 4 way
2. RJ11 – large 4 way
3. RJ way
4. RJ45 – 8way
5. Cable for each above
6. CAT5 cable
Possible Communication Cables needed
1. SAM1.5
2. SAM2, SAM3 & Access Control
3. Energy Meter (Landis & Gyrr) Rectifier
4. Rectifier (Battery Tech, Grintek, ASM, etc)
5. Generator (Lovato, Deep Sea, Intellilite, etc)
6. Fuel Cell (Idatech, Gencore, etc)
SAM Training

8. ECS-L Communication wiring SAM2 & Access Control
SAM Training

9. ECS-L Communication wiring SAM1.5
SAM Training

10. ECS-L Communication wiring landis & Gyrr
SAM Training

11. ECS-L Communication wiring battery tech SM65
SAM Training

12. ECS-L Communication wiring battery tech SM50
SAM Training

13. ECS-L Communication wiring Grintek GT500
SAM Training

14. ECS-L Communication wiring Lovato
SAM Training

15. Thank you