1. 1 CHM 585/490 Chapter 19 Semiconductors

2. 2 The market for imaging chemicals – photoresists, developers, strippers, and etchants – for the combined semiconductor and printed wiring board applications is in excess of $3 billion

3. 3 Moore’s Law

4. 4 It’s not a Law of Nature, but it comes close. In 1965, Intel co-founder Gordon Moore made the observation that has become known as Moore’s Law: the number of devices on a single chip (and the chip’s potential performance) doubles every year or so.

5. 5 Integrated circuits – millions of transistors layered on fingernail-sized chips of silicon. After 30 years of operation under Moore’s Law, manufacturers have reduced circuit patterns to incredibly thin line widths – pushing 0.18 microns, less than 1/160 the width of a human hair.

6. 6

7. 7

8. 8 Lithography Photosensitive polymer film is exposed to light to alter the solubility. If the exposed area of the resist film becomes insoluble after light exposure, then the resist is termed “negative” If the exposed area becomes more soluble – ‘positive” photoresist

9. 9 Photoresists In certain applications, the film becomes a permanent, functional component of the device being constructed, typically serving as an electrical insulator or protective encapsulant Most commonly, the resist is removed or “stripped” after the image has been transferred to the substrate.

10. 10 Essential Attributes of Lithographic Resists Must form uniform defect-free films on the substrate Coated film must display adequate adhesion to the substrate Must have suitable radiation sensitivity. Exposure tools are so costly that throughput is a key measure of performance.

11. 11 Diazonapthoquinone inhibits solubility of Novolac resin in base

12. 12

13. 13 Wavelength In any optical imaging system, the size of the smallest element that can be accurately resolved is related to the wavelength of exposing light. The smaller the wavelength, the finer the feature that can be resolved

14. 14 Need Lower Wavelengths New resists are designed for imaging with light of 193 nanometer wavelength Aromatic materials are opaque in this region Many newer resists based upon acrylate copolymers

15. 15 MMA for organic solubility, low shrinkage, adhesion and mechanical properties TBMA for acid catalyzed deprotection MAA for aqueous base solubility and increased T g

16. 16 Acid photochemically generated.

17. 17 Many other uses for polymers in microelectronic applications Adhesives Conductive adhesives Interlayer dielectrics Glob Top

18. 18 Some microelectronic polymers Polyimides Epoxies BCBs Parylenes

19. 19 Polyimides Kapton

20. 20 Polyimides Kapton

21. 21 Epoxies Epoxy resins are high-performance thermosetting resins. High performance coatings continue to be the primary application worldwide; electrical-electronic laminates, adhesives, flooring and paving applications, composites, and tooling and molding products are the other major end uses. Industrialized nations are by far the largest producers and consumers of epoxy resins

22. 22 In 1999, the estimated epoxy resin production value for the United States, Western Europe and Japan was over $2 billion. In 1999, almost 650 thousand metric tons of epoxy resins were consumed in the United States, Western Europe and Japan combined. Between 1999 and 2004, overall growth in epoxy resin demand is expected to average about 3.2% per year in the United States

23. 23 The three leading producers of epoxy resins are Resolution (formerly Shell's Epoxy Resins and Versatics business), Dow and Vantico. Together they account for approximately 75% of the world's capacity.

24. 24

25. 25

26. 26 Dow BCB Resins Low dielectric constant Low loss at high frequency Low moisture absorption Low cure temperature High degree of planarization Low level of ionics High optical clarity Good thermal stability Excellent chemical resistance Good compatibility with various metallization systems

27. 27 Diels Alder Reactions

28. 28 BCBs

29. 29

30. 30 Parylenes Used for conformal coatings

31. 31 Parylene Polymerization