Download presentation
Presentation is loading. Please wait.
1
6.1 Chapter 6 Bandwidth Utilization: Multiplexing and Spreading Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
2
6.2 Bandwidth utilization is the wise use of available bandwidth to achieve specific goals. Efficiency can be achieved by multiplexing; privacy and anti-jamming can be achieved by spreading. Note
3
6.3 6-1 MULTIPLEXING Whenever the bandwidth of a medium linking two devices is greater than the bandwidth needs of the devices, the link can be shared. Multiplexing is the set of techniques that allows the simultaneous transmission of multiple signals across a single data link. As data and telecommunications use increases, so does traffic. Frequency-Division Multiplexing Wavelength-Division Multiplexing Synchronous Time-Division Multiplexing Statistical Time-Division Multiplexing Topics discussed in this section:
4
6.4 Figure 6.1 Dividing a link into channels
5
6.5 Figure 6.2 Categories of multiplexing
6
6.6 Figure 6.3 Frequency-division multiplexing
7
6.7 FDM is an analog multiplexing technique that combines analog signals. Note
8
6.8 Figure 6.4 FDM process
9
6.9 Figure 6.5 FDM demultiplexing example
10
6.10 Assume that a voice channel occupies a bandwidth of 4 kHz. We need to combine three voice channels into a link with a bandwidth of 12 kHz, from 20 to 32 kHz. Show the configuration, using the frequency domain. Assume there are no guard bands. Solution We shift (modulate) each of the three voice channels to a different bandwidth, as shown in Figure 6.6. We use the 20- to 24-kHz bandwidth for the first channel, the 24- to 28-kHz bandwidth for the second channel, and the 28- to 32-kHz bandwidth for the third one. Then we combine them as shown in Figure 6.6. Example 6.1
11
6.11 Figure 6.6 Example 6.1
12
6.12 Figure 6.9 Analog hierarchy
13
6.13 Figure 6.10 Wavelength-division multiplexing
14
6.14 WDM is an analog multiplexing technique to combine optical signals. Note
15
6.15 Figure 6.11 Prisms in wavelength-division multiplexing and demultiplexing
16
6.16 Figure 6.12 TDM
17
6.17 TDM is a digital multiplexing technique for combining several low-rate channels into one high-rate one. Note
18
6.18 Figure 6.13 Synchronous time-division multiplexing
19
6.19 In synchronous TDM, the data rate of the link is n times faster, and the unit duration is n times shorter. Note
20
6.20 Figure 6.15 Interleaving
21
6.21 Figure 6.18 Empty slots
22
6.22 Figure 6.19 Multilevel multiplexing
23
6.23 Figure 6.20 Multiple-slot multiplexing
24
6.24 Figure 6.21 Pulse stuffing
25
6.25 Figure 6.22 Framing bits
26
6.26 Figure 6.23 Digital hierarchy
27
6.27 Table 6.1 DS and T line rates
28
6.28 Figure 6.24 T-1 line for multiplexing telephone lines
29
6.29 Figure 6.25 T-1 frame structure
30
6.30 Figure 6.26 TDM slot comparison
31
6.31 6-1 SPREAD SPECTRUM In spread spectrum (SS), we combine signals from different sources to fit into a larger bandwidth, but our goals are to prevent eavesdropping and jamming. To achieve these goals, spread spectrum techniques add redundancy. Frequency Hopping Spread Spectrum (FHSS) Direct Sequence Spread Spectrum Synchronous (DSSS) Topics discussed in this section:
32
6.32 Figure 6.27 Spread spectrum
33
6.33 Figure 6.28 Frequency hopping spread spectrum (FHSS)
34
6.34 Figure 6.29 Frequency selection in FHSS
35
6.35 Figure 6.30 FHSS cycles
36
6.36 Figure 6.31 Bandwidth sharing
37
6.37 Figure 6.32 DSSS
38
6.38 Figure 6.33 DSSS example
Similar presentations
