1. WeldFit Push-in Fittings

2. WeldFit Push-in Fittings
For use with WeldTube to protect against damage from weld spatter.
Easy tube insertion and removal
Tube support for retention under high loads
Recessed collet to prevent exposure of inner tube under side loads
Corrosion resistant nickel plated
Sizes G1/8, G1/4, G3/8, G1/2
Inner tube 6, 8, 10, 12mm o/d
For compressed air or water 41

3. WeldFit component parts
Recessed collet
Multiple teeth
‘O’ Ring
Tube support
Body
Sealing washer
Temperature range -300C to 700C
Materials Corrosion resistant nickel plated brass components Nitrile ‘O’ Ring Polyamide washer

4. WeldFit push-in fittings
Tube preparation
WeldFit push-in fittings

5. Tube preparation
Using a standard tube cutter, cut the complete tube end square at one of the markers.
Ensure that the tube end is clean and free from surface damage
900

6. Tube preparation
To prevent damage to the inner tube. Use the special stripping tool to cut the outer cover at the next marker

7. Tube preparation Push open the tube grip
Insert the cut to length tube and line up the next marker with the blade
Close the tube grip and rotate the stripper around the circumference of the tube

8. Tube preparation Push open the tube grip
Insert the cut to length tube and line up the next marker with the blade
Close the tube grip and rotate the stripper around the circumference of the tube

9. Tube preparation Push open the tube grip
Insert the cut to length tube and line up the next marker with the blade
Close the tube grip and rotate the stripper around the circumference of the tube

10. Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering

11. Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering

12. Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering

13. Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering

14. Tube and fitting assembly
WeldFit push-in fittings

15. Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied 42

16. Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied 42

17. Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied 42

18. Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied 42

19. Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied 42

20. WeldFit push-in fittings
Tube removal
WeldFit push-in fittings

21. Tube removal Turn off and exhaust the pressure
To remove the tube, push the collet in firmly and hold it there.
Pull the tube out and release the collet 42

22. Tube removal Turn off and exhaust the pressure
To remove the tube, push the collet in firmly and hold it there.
Pull the tube out and release the collet 42

23. Tube removal Turn off and exhaust the pressure
To remove the tube, push the collet in firmly and hold it there.
Pull the tube out and release the collet 42

24. Tube removal Turn off and exhaust the pressure
To remove the tube, push the collet in firmly and hold it there.
Pull the tube out and release the collet 42

25. WeldFit push-in fittings
The range
WeldFit push-in fittings

26. WeldFit Push-in Fittings
Included in the range:
Straight adaptors
Straight connectors
Elbow connectors
Tee connectors
900 Swivel adaptors
450 Swivel adaptors
Banjo assembly range

27. WeldTube range

28. Tube range
Four tube sizes each with outer tube colours in a choice of black, blue, green or red.
Inner tube o/d 6,8,10 and 12 mm (4,6,7,9 mm id)
Outer tube o/d 8,10,12.5,14.5 mm

29. Tube range
Minimum recommended bend radius
40, 50, 65 and 75 mm

30. End