1. APS-2 Single Pixel Test 7 February 2008 V. Suntharalingam  The Pattern file to capture data from a 256x256 array was modified to address only one pixel. Rather than building a new pattern from scratch, I modified an existing pattern file (it was quicker)  The readout mode for the “array” is what I have referred to as “Mode-1 Row Reset” –Each row is allowed to reset, integrate, and readout before going on to the next row –So for a single pixel address, after RESET the pixel is READ 256 times, and this Reset+256xRead is repeated 256 times (diagram on next slides) –The READ function is indicated by the TRIGGER signal, which goes to the ADC  The ascii data files are 256x256 ADU values captured by the NI ADC card (-2048 to +2048) –Since the imager operates on a row-by-row reset, each “row” of data is 256 samples after a single reset. The next row is data after a new reset  Measurement conditions: –Sample rate = 1MHz sample clock –Dark with NO CDS –VDDA = VDDD = VDD_ESD = 3.3V; VRST1 = VRST2 = 1.5V; PD = 5V –ADC input capture range = +/1V or +/-200mV, both with Voffset=1.30V  Please email/call if you have any questions 2/12/08 – Correction: pattern file displays in waveform editor at 200kHz (5µsec/sample) not 4MHz Testing was done at 1MHz-GUI which translates to 500kHz ADC trigger frequency

2. General Timing Diagram – Mode 1

3. (1) Address only Pixel r95c159: 65.5k times in cycle (RESET, READ) Trigger for ADC captureColumn Sample/Hold pulsing Timescale Here is for 200kHz sample clock Data taken with 1MHz sample clock RSTG1 pulsingRSTG2 pulsing

4. (2) Like previous, but Column SHS always ON Timescale Here is for 200kHz sample clock Data taken with 1MHz sample clock Column Sample/Hold always conducting (to see if it contributes noise) RSTG1 pulsingRSTG2 pulsing Ignore this display artifact

5. (3a) Like first, but RSTG1 ON to fix first stage to DC level of VRST1 Timescale Here is for 200kHz sample clock Data taken with 1MHz sample clock RSTG1 LOW Holds first stage to VRST1 RSTG2 pulsingColumn Sample/Hold pulsing

6. (3b) Timescale Magnification: Pixel is read 256x after RSTG2 and SHS SHS asserted for each “Row”, ADC Triggered 256x after each RESET Timescale Here is for 200kHz sample clock Data taken with 1MHz sample clock This waveform helps us evaluate how long the charge is held on the SHS capacitor

7. (4a) Like first, but Colmn SHS always on and RSTG1 always ON Timescale Here is for 200kHz sample clock Data taken with 1MHz sample clock RSTG1 LOW Holds first stage to VRST1 RSTG2 pulsingColumn Sample/Hold always conducting (to see if it contributes noise)

8. (4b) Timescale Magnification: Pixel is read 256x after RSTG2 SHS always HIGH, ADC Triggered 256x after each RESET Timescale Here is for 200kHz sample clock Data taken with 1MHz sample clock

9. Data Files Like slide #3, condition (1) w3r2c3_pixr95c159_m1_1M_RST15_PD5_voff130_1Vivr_dark.txt w3r2c3_pixr95c159_m1_1M_RST15_PD5_voff130_200mVivr_dark.txt Like slides #5-6, condition (3) w3r2c3_pixr95c159_m1RG1Low_1M_RST15_PD5_voff130_1Vivr_dark.txt w3r2c3_pixr95c159_m1RG1Low_1M_RST15_PD5_voff130_200mVivr_dark.txt Like slides #7-8, condition (4) w3r2c3_pixr95c159_m1RG1LowSHSHigh_1M_RST15_PD5_voff130_1Vivr_dark.txt w3r2c3_pixr95c159_m1RG1LowSHSHigh_1M_RST15_PD5_voff130_200mVivr_dark.txt +/-1V ADC Input capture range 1 ADU = 2/4096 +/-200mV ADC Input capture range 1 ADU = 0.4/4096