1. Th, Pu & U Separation Using TEVA and UTEVA Resin
Eichrom Workshop at RRMC
12 November, 2002
Knoxville, TN

2. Objective To develop a quick method for the separation of
Th, Pu and U in water samples

5. Tracers U232 tracer cleanup required to remove daughter Th228
Followed David Sill (NAREL)’s BaSO4 procedure
Pu242 and Th229 used for plutonium and thorium
Pu236 better choice if Np measurement is required

6. Sample Preparation
1 liter aliquots of acidified water samples were spiked with Th229, Pu242 and U232 tracers
Samples were heated to near boiling for 2 hours
A Ca3(PO4)2 precipitation was performed
Decant supernatant, centrifuge and collect the precipitate

7. Load Solution Dissolve precipitate in 3M HNO3/1M Al(NO3)3 solution
Add ferrous sulfamate and NaNO2
Load on TEVA and UTEVA Resin cartridge in tandem

8. Proposed Procedure
1) Attach TEVA resin and UTEVA resin cartridges in tandem
2) Load 10 ml of 3M HNO3/1M Al(N03)3. with 2 mL of 0.6M Ferrous sulfamate followed with 1 ml of 3M NaNO2
3) Rinse sample beaker with 5 mL of 3M HNO3
4) Rinse cartridge with 5 mL of 3M HNO3
5) Separate TEVA and UTEVA cartridges

9. Proposed Procedure continued
TEVA cartridge
1) Rinse with 30 ml of 3M HNO3
2) Elute Th with 20 ml of 9M HCl and 5 ml of 6M HCl
3) Elute Pu with 20 ml of 0.02M TiCl3/0.05M HCl/0.05M HF (Np eluted in this fraction)

10. Proposed Procedure continued
UTEVA Cartridge
1) Rinse with 5 ml of 9M HCl
2) Elute U with 15 ml of 1M HCl

11. Direct Spike Results (Proposed Procedure)

12. U fraction contaminated with Pu

13. Improvements Needed
Possible Pu valence adjustment for better recoveries
U recoveries need to be higher
Better decontamination for U fraction

14. Possible Solutions for Improvements
1) Use 2 ml of ferrous sulfamate ml of NaNO2
2) Use 1 ml of ferrous sulfamate + 1 ml of NaNO2
3) Increase U and Pu strip volumes
4) Add oxalic acid rinse on UTEVA

15. Direct Spike Results (2 ml of Ferrous+0.5ml of NaNO2 )
* With 25 ml of Pu strip volume
**With 20 ml of U strip volume & oxalic acid rinse

16. Direct Spike Results (1 ml of Ferrous + 1ml of NaNO2)
*With 25 ml of Pu strip volume
**With 20 ml of U strip volume & oxalic acid rinse

17. Revised Procedure
1) Load sample on TEVA resin and UTEVA resin cartridges in tandem with 10 ml of 3M HNO3/1M Al(N03)3. with 1.0 mL of 0.6M ferrous sulfamate and 1 ml of 3M NaNO2
2) Rinse sample beaker with 5 mL of 3M HNO3
3) Rinse cartridge with 5 mL of 3M HNO3
4) Separate TEVA and UTEVA cartridges

18. ACW13 continued TEVA cartridge 1) Rinse with 5 ml of 3M HNO3
3) Elute Th with 20 ml of 9M HCl and 5 ml of 6M HCl
4) Elute Pu with 25 ml of 0.02M TiCl3/0.05M HCl/0.05M HF (Np will be present in this fraction)

19. Revised ACW13 continued UTEVA Cartridge 1) Rinse with 5 ml of 3M HNO3
2) Rinse with 5 ml of 9M HCl
3) Rinse with 20 ml of 5M HCl/0.05M oxalic acid
4) Elute U with 20 ml of 1M HCl

20. Decontamination Test
~100 pCi of Am, Np, Th, Pu and U were added to the load solution
Solution was processed following ACW13

21. Decontamination Factors

22. DI Water

23. Th229 Spectrum

24. U232 Spectrum

25. Pu242 Spectrum

26. Tap Water

27. Summary Benefits Drawbacks
A quick method with consistent, reproducible recoveries
Rugged enough to provide good decontamination from other actinides
Drawbacks
Th228 cleanup required
Pu236 tracer required if Np237 measured