1. Instructions www.supertramp.co.uk 1

2.  SITING YOUR TRAMPOLINE  Your trampoline works best and is safest if it is dead level. If your trampoline is fitted with a safety enclosure then potential hazards within 2 metres of the trampoline like paving stones, fences, pools, tree trunks and buildings will not be critical. Without a safety enclosure it is vital to keep clear 2 metres of lawn space all round the trampoline.  Always ensure that the area above the trampoline is clear of overhead cable and branches. Even if the cables and branches are way up high, birds will roost on them and use your trampoline for target practice.  Garden trampolines are designed to stand on a lawn. If they are on concrete or gravel the underside of the leg bases will wear away quite quickly. If you are planning to site your Trampoline on concrete or on a patio you should fix floor guards to your Trampoline legs.  If you need to level your trampoline try and raise one side by the same distance that you sink the other. That way you still have sufficient clearance beneath the trampoline to prevent larger and more energetic bouncers bottoming out and hitting the ground. Unless the slope is very slight just blocking up the lower legs will not work well as the trampoline will tend to move down the slope and fall off the blocks. It is better to create a groove for the uphill legs to rest in or alternatively ground anchor them so they cannot creep down hill. A quick and simple way to check that your trampoline is level is to take off a spring and see if it will roll downhill on the trampoline bed. 2

3. Part10ft12ft14ft Top Rails 688 Leg Bases 344 Leg Extension 688 Springs 54 X 5.5 inch 72 X 7 inch 80 X 7 inch Jumping Bed 111 Frame Pads 111 3

4. a) Lay frame parts out on a reasonably level part of lawn. b) Assemble trampoline LEGS by sliding onto LEG BASE c) Once you have joined the leg extensions to the leg bases start linking them together by fitting the top rail d) Work around the trampoline to complete your frame 4

5. a) Unfold the black poly-mesh bed on the ground inside the completed trampoline frame b) Before fitting any springs, note that the extended hook on each spring fits into the frame and the smaller hook fits into the triangular anchor on the bed. c) Fit one spring into the slot just to the right hand side of a top rail joiner then attach the spring to the bed on the inside of the frame d) Then work your way round the frame and attach a spring immediately to the right of each top rail joiner and to the appropriate triangle on the bed e) Then lay out the ESN Net onto the trampoline and attach a the 8 points making sure that the plastic bungee holders on the net are lined up with the T sections THIS IS VERY IMPORTANT OVERWISE YOU WILL TWIST THE NET f) Fill in the gaps by attaching springs midway between each of those already fitted spring including counting the net holes. g) Repeat until all of the springs and net are attached. 5

6. 6

7. a) Place the frame pads on the trampoline and line up the enclosure pole holes with the T section top rail joiners a) Then attach the pads using the spring loops on the pads, do this by un clipping a spring placing it through the loop and reattaching the spring. 7

8. a) Place the bottom enclosure poles though the pad hole and into the slot underneath in the T joiner a) Complete the assembly by using the nut and bolt provided a) Then clip on the top poles using the screws provided. 8

9. a) Attach the net using the Bungee loops provided place these through top poles then attach onto the net. Do this all the way around the trampoline. b) Now that all the trampoline poles are attached to the net go to each pole and lift into the bottom pole that is already attached to the trampoline, do this all the way around the trampoline. c) Note some poles will start hanging as you work round this is nothing to worry about. d) Once this is done check through trampoline before use. Congratulations you have Complete your trampoline 9

10. Products10ft12ft14ft Enclosure Net111 Bottom poles with foam 688 Top poles with foam 688 Enclosure toggle loops 111 Nuts and Bolts + Spanner Pack 111 10

11. If the trampoline is bigger than 8ft we provide a ladder so that it is easier to enter and exit the trampoline a) Attach the ladder base using the ball catch b) Attach each ladder step to the two uprights ensuring they fit correctly (step facing you, bolt to the front using the nut on the back c) Fasten each step securely using the spanner provided 11

12. IMPORTANT Please keep your proof of purchase it will be needed to make a claim * Ladder – 1 year guarantee 12

13. Twitter : Feel free to tweet us a picture of your trampoline @supertrampuk @JetSportsLtd Facebook: https://www.facebook.com/supertrampltdhttps://www.facebook.com/supertrampltd Pinterest: http://www.pinterest.com/jetsportsltd/pins/http://www.pinterest.com/jetsportsltd/pins/ 13

14. For more information on trampolines check out Get Britain Bouncing and for spare parts visit our website www.supertramp.co.ukwww.getbritainbouncing.org.uk 14