1. EPack relaunch

2. Schneider Electric 2 -Industrial – Eurotherm – 16/12/2015 ●1. Reduce your equipment costs

3. Schneider Electric 3 -Industrial – Eurotherm – 16/12/2015 EPack - What is it?  A new range of power controllers  1 phase products for the moment  Complement range to Epower  Low to middle current ratings (16A to 125A)  Advanced product (levels 1 and 2)

4. Schneider Electric 4 -Industrial – Eurotherm – 16/12/2015 General overview Coloured TFT display Dual Ethernet port Connexions line/load Touch buttons Inputs/Outputs Supplies Voltage reference Line connexion Auxiliary supplies Load connexion Analog./ Digital inputs Relay

5. Schneider Electric 5 -Industrial – Eurotherm – 16/12/2015 Hardware variants EPack is fully configurable/upgradable except : -The mechanics (32A, 63A, 100A or 125A) -The voltage of the auxiliary voltage (24V AC/DC or 100-500V AC)  These options require a different build of the product and can’t be changed in the field. 32A63A 100A125A

6. Schneider Electric 6 -Industrial – Eurotherm – 16/12/2015 The product is equipped with two supplies : o Power > thyristor o Auxiliary > comms and display Why?  We cannot use power voltage for configuration  Potential at the output of the product at 0% of setpoint => Safety issues  To run comms even in case of power fault  Can provide diagnostics in every condition  To be able to configure the product without dangerous voltage  Configuration can be made with presence of 24V only Supplies

7. Schneider Electric 7 -Industrial – Eurotherm – 16/12/2015 All firing modes are available in standard  Burst modes  Fixed burst (100 periods by default, adjustable from 25 to 1000)  Variable burst (16 periods by default, adjustable from 1 to 100)  Intelligent half cycle  Phase angle  Progressive start-up (phase angle ramp)  Delay triggering (First firing delay)  Switch phase angle/ burst Firing modes

8. Schneider Electric 8 -Industrial – Eurotherm – 16/12/2015 EPack is able to deliver the power based on the following controls  V² control  Suitable for pure resistive loads (constant resistance)  V² control with current limit (V2CL)  Suitable for primaries of transformers with pure resistive loads  I² control  Suitable for HTCL loads / bushing  True Power control  Suitable whose resistance changes according to age or temperature (TTDL) Control modes

9. Schneider Electric 9 -Industrial – Eurotherm – 16/12/2015 IO connector (5 points)  1 analog input fully configurable  Function : SP, limit….  Type : 0-5V, 1-5V, 0-10V, 2-10V, 0-20mA, 4-20mA  2 digital inputs fully configurable  Function DI1 : enable signal by default  Function DI2 : fully configurable  Type : voltage or contact Relay connector (3 points)  2A relays  2 contacts (NO and NC) I/O and relay

10. Schneider Electric 10 -Industrial – Eurotherm – 16/12/2015 1.Complete oder code – 19 fields  Defines completely the product : fit for purpose  No adjustment in case of replacement 2.Quick code – 11 fields  Hardware and software options defined by order code  Configuration through set of questions  More than 80% of applications are covered 3.Itools  Same as quick code for HW and SW definition  Access to all parameters of the product / with help available  Saving and cloning capabilities 3 configuration methods

11. Schneider Electric 11 -Industrial – Eurotherm – 16/12/2015  Protocol  Modbus TCP for the moment  Other protocols to come…  Connection  Direct  Through a switch  Daisy chain  Cable  Straight  Cross  Used for  Itools configuration  Fieldbus connection Dual Ethernet port with integrated switch Comms

12. Schneider Electric 12 -Industrial – Eurotherm – 16/12/2015  What is it?  Zero configuration networking (zeroconf) is a set of techniques that automatically creates a usable Internet Protocol (IP) network without manual operator intervention or special configuration servers  How does it work?  It allocates dynamically the IP addresses to the slaves if no address is affected by DHCP server (Auto-IP)  What does it result in?  A plug a play Ethernet connection! Zero conf protocol

13. Schneider Electric 13 -Industrial – Eurotherm – 16/12/2015 No internal fuse Fusing methods depends on the option  Without fuse  for loads generating high surge current (typically SWIR)  Requires protection against overloads and short circuit  High speed fuse  Protect thyristor against short circuit  Requires additional line protection Fuse options

14. Schneider Electric 14 -Industrial – Eurotherm – 16/12/2015 StandardChargeable Firing modesAll modesNone Control modesV², V²CLI², True Power TransferWithoutI² transfer Input typesAll typesNone 32A mechanics16A25A, 32A 63A mechanics40A50A,63A 100A mechanics80A100A FuseWithoutYes Energy counterWithoutyes Graphical wiringWithoutyes Custom labellingEurotherm labelyes Standard vs options

15. Schneider Electric 15 -Industrial – Eurotherm – 16/12/2015 24V version 500V version Typical schemes

16. Schneider Electric 16 -Industrial – Eurotherm – 16/12/2015 Standards 1.Product standard IEC 60947-4-3 2.UL/c-UL 60947 with SCCR @ 100kA 3.RoHS (RoHS 2 pending) 4.GOST exemption 5.CCC self certification