1. Products Engineering Dept.
SPECIFICATION
FOR
APPROVAL ( ◆ )
Preliminary Specification
Final Specification
Title
13.3” WXGA TFT LCD
BUYER
APPLE
MODEL
SUPPLIER
LG.Philips LCD Co., Ltd.
*MODEL
LP133WX1
Suffix
TLA1
*When you obtain standard approval,
please use the above model name without suffix
APPROVED BY
SIGNATURE /
Please return 1 copy for your confirmation with
your signature and comments.
APPROVED BY
SIGNATURE
J. H. Lee / G.Manager
REVIEWED BY
G. J. Han / Manager
K. S. Byun / Manager
PREPARED BY
J. H. Park / Engineer
C. H. Lee / Engineer
Products Engineering Dept.
LG. Philips LCD Co., Ltd

2. Contents No ITEM Page COVER 1 CONTENTS 2 RECORD OF REVISIONS 3
GENERAL DESCRIPTION 4
ABSOLUTE MAXIMUM RATINGS 5
ELECTRICAL SPECIFICATIONS
3-1
ELECTRICAL CHARACTERISTICS 6
3-2
INTERFACE CONNECTIONS 8
3-3
SIGNAL TIMING SPECIFICATIONS 9
3-4
SIGNAL TIMING WAVEFORMS
3-5
COLOR INPUT DATA REFERNECE 10
3-6
POWER SEQUENCE 11
OPTICAL SPECIFICATIONS 12
MECHANICAL CHARACTERISTICS 16
RELIABILITY 20 7
INTERNATIONAL STANDARDS
7-1
SAFETY 21
7-2
EMC
PACKING
8-1
DESIGNATION OF LOT MARK 22
8-2
PACKING FORM
PRECAUTIONS 23 A
APPENDIX A. Enhanced Extended Display Identification Data 25

3. RECORD OF REVISIONS Revision No Revision Date Page Description EEDID
Ver.
0.0
Nov -
Preliminary Specification
V0.0

4. 1. General Description General Features
The LP133WX1-TLA1 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Lamp (CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFT-LCD has 13.3 inches diagonally measured active display area with WXGA resolution(800 vertical by 1280 horizontal pixel array). Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors.
The LP133WX1-TLA1 has been designed to apply the interface method that enables low power, high speed, low EMI.
The LP133WX1-TLA1 is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LP133WX1-TLA1 characteristics provide an excellent flat display for office automation products such as Notebook PC.
CN1
LVDS
&
Timing
Control
Block
Power
Column Driver Circuit
Row Driver Circuit
TFT-LCD
(1280 X 800)
Backlight Lamp Ass'y J1
:Control & Data
:Power
General Features
Active Screen Size
13.3 inches diagonal
Outline Dimension
299.0(H)[typ.] × 195.0(V)[typ.] × 5.5(D) mm [Max.]
Pixel Pitch
mm × mm
Pixel Format
1280 horiz. By 800 vert. Pixels RGB strip arrangement
Color Depth
6-bit, 262,144 colors
Luminance, White
250 cd/m2[typ.], 5p average
Power Consumption
Total 4.5 LCM circuit 0.7 Watt(Typ.), B/L input 3.8 Watt(Typ.)
Weight
350g [Max.] , 360g [Typ.]
Display Operating Mode
Transmissive mode, normally white
Surface Treatment
Hard coating(2H) Anti-Reflection treatment of the front polarizer

5. 2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Values
Units
Notes
Min
Max
Power Input Voltage
VCC
-0.3
4.0
Vdc
at 25  5C
Operating Temperature
TOP 50 C 1
Storage Temperature
HST
-20 60
Operating Ambient Humidity
HOP 10 90
%RH
Storage Humidity
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39C Max, and no condensation of water. 10 20 30 40 50 60 70 80
-20
Dry Bulb Temperature [℃]
10%
20%
40%
60%
90%
80%
Wet Bulb
Temperature [℃]
Humidity[(%)RH]
Storage
Operation

6. Table 2. ELECTRICAL CHARACTERISTICS
3. Electrical Specifications
3-1. Electrical Characteristics
The LP133WX1-TLA1 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input which powers the CCFL, is typically generated by an
inverter. The inverter is an external unit to the LCD.
Table 2. ELECTRICAL CHARACTERISTICS
Parameter
Symbol
Values
Unit
Notes
Min
Typ
Max
MODULE :
Power Supply Input Voltage
VCC
3.0
3.3
3.6
Vdc
Power Supply Input Current
ICC -
215
245 mA
Mosaic
270
Black
Power Consumption Pc
0.8
0.9
Watts 1
Differential Impedance Zm 90
100
110
Ohm 2
LAMP :
Operating Voltage
VBL
595(7.0mA)
630(6.0mA)
845(2.0mA)
VRMS 3
Operating Current
IBL
2.0
6.0
7.0
mARMS 4
PBL
3.8
4.2
Operating Frequency
fBL 45 60 80
kHz 7
Discharge Stabilization Time Ts 5
Life Time
12,000
Hrs 6
Established Starting Voltage
at 25℃
at 0 ℃ Vs
1140
1370 8
Note)
1. The specified current and power consumption are under the Vcc = 3.3V , 25℃, fv = 60Hz condition
whereas black pattern is displayed and fv is the frame frequency.
2. This impedance value is needed to proper display and measured form LVDS Tx to the mating connector.
3. The variance of the voltage is ± 10%.
4. The typical operating current is for the typical surface luminance (LWH) in optical characteristics.
5. Define the brightness of the lamp after being lighted for 5 minutes as 100%, Ts is the time required for
the brightness of the center of the lamp to be not less than 95%.
6. The life time is determined as the time at which brightness of lamp is 50% compare to that of initial value
at the typical lamp current.
7. The output of the inverter must have symmetrical(negative and positive) voltage waveform and
symmetrical current waveform.(Asymmetrical ratio is less than 10%) Please do not use the inverter
which has asymmetrical voltage and asymmetrical current and spike wave.
Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may
cause beat on the display. Therefore lamp frequency shall be as away possible from the
horizontal synchronous frequency and from its harmonics in order to prevent interference.
8. The voltage above VS should be applied to the lamps for more than 1 second for start-up. Otherwise, the
lamps may not be turned on. The used lamp current is the lamp typical current.
9. The lamp power consumption shown above does not include loss of external inverter.
The applied lamp current is a typical one.

7. Note)
9. Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp, are following.
It shall help increase the lamp lifetime and reduce leakage current a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion rate of the waveform should be within √2 ±10%.
* Inverter output waveform had better be more similar to ideal sine wave.
※ Do not attach a conducting tape to lamp connecting wire.
If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter
has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.
I p
I -p
* Asymmetry rate:
| I p – I –p | / Irms * 100%
* Distortion rate
I p (or I –p) / Irms

8. 3-2. Interface Connections
This LCD employs two interface connections, a 20 pin connector is used for the module electronics interface and the other connector is used for the integral backlight system.
The electronics interface connector is a model DF manufactured by LGC.
Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)
Pin
Symbol
Description
Notes 1
GND
Ground 2
VCC
Power Supply, 3.3V Typ. 3 4
V EEDID
DDC 3.3V power 5 NC
No Connection 6
Clk EEDID
DDC Clock 7
DATA EEDID
DDC Data 8
RA1-
Odd Channel Differential signal 9
RA1+ 10 11
RB1- 12
RB1+ 13 14
RC1- 15
RC1+ 16 17
RCLK1- 18
RCLK1+ 19 20
RA2-
1, Interface chips
1.1 LCD : LVDS Receiver (THC63LVD824)
or equivalent
1.2 System : THC63LVD823A or equivalent
* Pin to Pin compatible with TI LVDS
2. Connector
2.1 LCD : DF19KR-20P-1H, HIROSE or
its compatibles
2.2 Mating : DF19G-20S-1C or equivalent.
2.3 Connector pin arrangement
CN1 1 20
Viewing on Display side
CN2 1 20
CN1
[LCD Module Rear View]
The backlight interface connector is a model BHSR-02VS-1, manufactured by JST or its compatibles .
The mating connector part number is SM02B-BHSS-1 or equivalent.
Table 4. BACKLIGHT CONNECTOR PIN CONFIGURATION (J3)
Pin
Symbol
Description
Notes 1 HV
Power supply for lamp (High voltage side) 2 LV
Power supply for lamp (Low voltage side)
Notes : 1. The high voltage side terminal is colored pink and the low voltage side terminal is yellow

9. 3-3. Signal Timing Specifications
This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications and specifications of LVDS Tx/Rx for it’s proper operation.
Table 6. TIMING TABLE
ITEM
Symbol
Min
Typ
Max
Unit
Note
DCLK
Frequency
fCLK
67.5
71.0
74.5
MHz
Hsync
Period
Thp
1366
1440
1488
tCLK
Width
tWH 16 32 48
Active
tWHA
1280
Vsync
tVP
811
823
847
tHP
tWV 3 6 9
tWVA
800
Data
Enable
Horizontal back porch
tHBP 54 80 98
Horizontal front porch
tHFP 62
Vertical back porch
tVBP 5 14 35
Vertical front porch
tVFP
3-4. Signal Timing Waveforms
Condition : VCC =3.3V
Low: 0.3VCC
High: 0.7VCC
Data Enable, Hsync, Vsync
Hsync
Data Enable
Vsync
tWH
tHP
tHFP
tHBP
tVP
tWV
tVBP
tVFP
tWHA
tWVA
tCLK
0.5 Vcc
DCLK

10. Table 7. COLOR DATA REFERENCE
3-5. Color Input Data Reference
The brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.
Table 7. COLOR DATA REFERENCE
Color
Input Color Data
RED
MSB LSB
GREEN
MSB LSB
BLUE
MSB LSB
R5 R4 R3 R2 R1 R0
G5 G4 G3 G2 G1 G0
B5 B4 B3 B2 B1 B0
Basic
Black
Red
Green
Blue
Cyan
Magenta
Yellow
White
RED (00)
RED (01) …
RED (62)
RED (63)
GREEN (00)
GREEN (01)
...
GREEN (62)
GREEN (63)
BLUE (00)
BLUE (01)
BLUE (62)
BLUE (63)

11. Table 8. POWER SEQUENCE TABLE
90%
90%
Power Supply For LCD
VCC
10%
10% 0V T7 T2 T6 T5 T1
Interface Signal, Vi
(LVDS Signal of Transmitter)
Valid Data 0V T3 T4
Power for Lamp
LAMP ON
OFF
OFF
Table 8. POWER SEQUENCE TABLE
Parameter
Value
Units
Min.
Typ.
Max. T1
0.5 - 10
(ms) T2 50 T3
200 T4 T5 T6 T7
Note)
1. Please avoid floating state of interface signal at invalid period.
2. When the interface signal is invalid, be sure to pull down the power supply for LCD VCC to 0V.
3. Lamp power must be turn on after power supply for LCD and interface signal are valid.

12. 4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes in a dark environment at 25C. The values specified are at an approximate distance 50cm from the LCD surface
at a viewing angle of  and  equal to 0.
FIG. 1 Presents additional information concerning the measurement equipment and method.
FIG. 1 Optical Characteristic Measurement Equipment and Method
LCD Module
Pritchard 880 or
equivalent
Optical Stage(x,y)
50cm
Table 9. OPTICAL CHARACTERISTICS
Ta=25C, VCC=3.3V, fV=60Hz, fCLK= 71.0MHz, Iout = 6.0mA
Parameter
Symbol
Values
Units
Notes
Min
Typ
MAx
Contrast Ratio CR
350
400 - 1
Surface Luminance, white
LWH
220
250
cd/m2 2
Luminance Variation
 WHITE
1.4
1.6 3
Response Time 4
Rise Time+Decay Time
TrR +TrD 25 35 ms
Color Coordinates
RED RX
TBD RY
GREEN GX GY
BLUE BX BY
WHITE WX
0.283
0.313
0.343 WY
0.299
0.329
0.359
Viewing Angle 5
x axis, right(=0) r 40 45
degree
x axis, left (=180) l
y axis, up (=90) u 10 15
y axis, down (=270) d 30
Gray Scale 6

13.  WHITE = Note) 1. Contrast Ratio(CR) is defined mathematically as
Surface Luminance with all white pixels
Contrast Ratio =
Surface Luminance with all black pixels
2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with
all pixels displaying white. For more information see FIG 1.
LWH = Average(L1,L2, … L5)
3. The variation in surface luminance , The panel total variation ( WHITE) is determined by measuring LN
at each test position 1 through 13 and then defined as followed numerical formula.
For more information see FIG 2.
Maximum(L1,L2, … L13)
 WHITE =
Minimum(L1,L2, … L13)
4. Response time is the time required for the display to transition from white to black (rise time, TrR) and
from black to white(Decay Time, TrD). For additional information see FIG 3.
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see FIG 4.
6. Gray scale specification * fV = 60Hz
Gray Level
Luminance [%] (Typ) L0
0.12 L7
0.97
L15
4.61
L23
11.4
L31
21.6
L39
35.4
L47
53.0
L55
74.5
L63
100

14. Tr H A D C B V Center Point FIG. 2 Luminance
<measuring point for surface luminance & measuring point for luminance variation> H A D L6 L7 L8
H,V : ACTIVE AREA
A : H/4 mm
B : V/4 mm
C : 10 mm
D : 10 mm
POINTS : 13 POINTS C L2 L3 B V L9 L1
L10
Center Point L4 L5
L11
L12
L13
FIG. 3 Response Time
The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”. Tr R D
100 90 10 %
Optical
Response
white
black

15. FIG. 4 Viewing angle
<Dimension of viewing angle range>

16. 5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP133WX1-TLA1.
In addition the figures in the next page are detailed mechanical drawing of the LCD.
Outline Dimension
Horizontal
299.0  0.5mm
Vertical
195.0  0.5mm
Depth
5.2mm(Typ.),5.5mm(Max.)
Bezel Area
289.5  0.3mm
182.2  0.3mm
Active Display Area mm
178.8 mm
Weight
350g(typ) , 360g(Max.)
Surface Treatment
Hard coating(2H), Anti-Reflection treatment of the front polarizer

17. <FRONT VIEW>

18. <REAR VIEW>

19. the conductive particles from screw surface.
[ DETAIL DESCRIPTION OF SIDE MOUNTING SCREW ]
* Mounting Screw depth
depth Min. : “A” =2.0
depth Max : “B” =2.3
* Mounting hole location : 2.8(typ.)
*Torque : 2 kgf.cm(Max)
(Measurement gauge : torque meter)
Notes : 1. Screw plated through the method of non-electrolytic nickel plating is preferred
to reduce possibility that results in vertical and/or horizontal line defect due to
the conductive particles from screw surface.

20. 6. Reliability Environment test condition No. Test Item Conditions 1
High temperature storage test
Ta= 60C, 240h 2
Low temperature storage test
Ta= -20C, 240h 3
High temperature operation test
Ta= 50C, 50%RH, 240h 4
Low temperature operation test
Ta= 0C, 240h 5
Vibration test
(non-operating)
Sine wave, 10 ~ 500 ~ 10Hz, 1.5G, 0.37oct/min
3 axis, 1hour/axis 6
Shock test
Half sine wave, 180G, 2ms
one shock of each six faces(I.e. run 180G 2ms
for all six faces) 7
Altitude operating
storage / shipment
0 ~ 10,000 feet (3,048m) 24Hr
0 ~ 40,000 feet (12,192m) 24Hr
{ Result Evaluation Criteria }
There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.

21. 7. International Standards
7-1. Safety
a) UL :2003, First Edition, Underwriters Laboratories, Inc.,
Standard for Safety of Information Technology Equipment.
b) CAN/CSA C22.2, No st Ed. April 1, 2003, Canadian Standards Association,
c) EN :2001, First Edition,
European Committee for Electrotechnical Standardization(CENELEC)
European Standard for Safety of Information Technology Equipment.
7-2. EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),
1992
b) C.I.S.P.R. “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ International Special Committee on Radio Interference.
c) EN “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ European Committee for Electrotechnical Standardization.(CENELEC), 1998
( Including A1: 2000 )

22. 8-1. Designation of Lot Mark
8. Packing
8-1. Designation of Lot Mark
a) Lot Mark A B C D E F G H I J K L M
A,B,C : SIZE(INCH) D : YEAR
E : MONTH F : FACTORY CODE
G : ASSEMBLY CODE H ~ M : SERIAL NO.
Note
1. YEAR
Mark
Year
2010 6
2006 7
2007 8
2008 9
2009 4
2004 5
2005 3 2 1
2003
2002
2001
2. MONTH B
Nov
Mark
Month A
Oct 6
Jun 7
Jul 8
Aug 9
Sep 4
Apr 5
May C 3 2 1
Dec
Mar
Feb
Jan
3. FACTORY CODE
Factory Code
LPL Gumi
LPL Nanjing
HEESUNG
Mark K C D
4. SERIAL NO.
Mark
100001~199999, ~299999, ~399999, …., A00001~A99999, ….., Z00001~Z99999
b) Location of Lot Mark
Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.
8-2. Packing Form
a) Package quantity in one box : pcs
b) Box Size : mm × mm × mm

23. 9-1. MOUNTING PRECAUTIONS
Please pay attention to the following when you use this TFT LCD module.
9-1. MOUNTING PRECAUTIONS
(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force(ex. Twisted stress) is not applied
to the module.
And the case on which a module is mounted should have sufficient strength so that external force
is not transmitted directly to the module.
(3) Please attach a transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not describe because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit
break by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are determined
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2. OPERATING PRECAUTIONS
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to
polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference
shall be done by system manufacturers. Grounding and shielding methods may be important to
minimized the interference.

24. 9-3. ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain
that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.
9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE
Strong light exposure causes degradation of polarizer and color filter.
9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM
(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.

25. APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 1/3

26. APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 2/3

27. APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 3/3