1. Design Process Analysis & Evaluation Part II Example Design: Solar Candle by Prof. Bitar

2. Existing Window Candle Block Diagram Solar Cell Charge Controller Rechargeable Battery 1.2V NiCd DC-DC Boost Converter LED 3.2V 20mA Flickering Control Mode Selection Photo Sensor

3. Diodes/Zetex - ZXLD383ET5CT

4. Typical Application Circuit Note Control Pin!

5. DC-DC Converter Efficiency

6. Modified System Block Diagram Solar Panel Charge Controller Rechargeable Battery 1.2V NiCd 700 mAhrs Zetex LED Driver 85% Eff. LED 20mA 3.2V(min) Switching Control Mode Selection Photo Sensor Timer

7. Changing Focus to Charging How much energy is removed from the battery during a typical evening? LED requires 20mA x 3.2V x 6hrs = 384 mW hrs (power x time = energy)LED requires 20mA x 3.2V x 6hrs = 384 mW hrs (power x time = energy) Converter is only 85% efficient, so energy taken from battery is 384 mW hrs / 0.85 ≈ 452 mW hrsConverter is only 85% efficient, so energy taken from battery is 384 mW hrs / 0.85 ≈ 452 mW hrs How much charge? Dividing by the battery voltage gives the charge removed: 452 mW hrs / 1.2V ≈ 377 mA hrsDividing by the battery voltage gives the charge removed: 452 mW hrs / 1.2V ≈ 377 mA hrs

8. The Prior Art Dissected

9. On to the Solar Panel Requirements After taking the Home Depot Landscape Light apart, I made the following measurements (in direct sun): I SC = 50mA, V OC = 4.3V

10. Solar Panel V-I Characteristic

11. Solar Panel Considerations How much charge is restored if the panel is connected directly to the battery? What assumptions should we make? How about 10 Hours of Daylight10 Hours of Daylight 50% Incident Light50% Incident Light This gives 50mA x 10hrs x 50% = 250mA hrs Is this enough? We need 377 mA hrs. No. 

12. Charge Options? Use two solar panels in parallel to boost the current (although we seem to be throwing away the excess voltage?) Modify the existing panel for higher current (at the expense of voltage).

13. Modified Solar Panel Configuration

14. Modified Characteristic I SC = 100 mA, V OC = 2.15 V (V OC still greater than V BAT )

15. A Possible Solution Now we have: 100mA x 10 hrs x 50% = 500 mA hrs. Is this enough? We need 377mA hrs. Yes! Is this enough? We need 377mA hrs. Yes!

16. Solar Panel Update to System Block Diagram Solar Panel I SC = 100mA V OC = 2.15V I AVE = 50mA Δt = 10hrs Q = 500mAHrs Charge Controller Rechargeable Battery 1.2V NiCd Zetex LED Driver LED 20mA 3.2V(min) Switching Control Mode Selection Photo Sensor Timer

17. And now the Charge Controller… Solar Panel I SC = 100mA V OC = 2.15V I AVE = 50mA Δt = 10hrs Q = 500mAHrs Charge Controller Rechargeable Battery 1.2V NiCd Zetex LED Driver LED 20mA 3.2V(min) Switching Control Mode Selection Photo Sensor Timer

18. NiCd Charge Control Methods (Panasonic)

19. Which Charge Method to Choose? Semi-Constant Current Charge Most Typical Charge System Most Typical Charge System Simple and Economical Simple and Economical Typical Charge Time = 15 Hrs Typical Charge Time = 15 Hrs Typical Charge Current = 0.1 It Typical Charge Current = 0.1 It (0.1*700 mA Hrs = 70mA) Time Controlled Charge More reliable than Semi-Constant Current More reliable than Semi-Constant Current Slightly more complicated. Requires timer. Slightly more complicated. Requires timer. Typical Charge Time = 6-8 Hrs Typical Charge Time = 6-8 Hrs Typical Charge Current = 0.2 It (140mA) Typical Charge Current = 0.2 It (140mA)

20. Semi-Constant Current Charge Seems Viable With our low average current of 50mA, and charge time of 10 hrs, the Semi- Constant Current Charge method seems viable. Also, if we are concerned about over charge, we can extend the on-time beyond 6 hrs. This method is more economical and may not require a timer for this application.

21. Charge Controller Update Solar Panel I SC = 100mA V OC = 2.15V I AVE = 50mA Δt = 10hrs Q = 500mAHrs Charge Controller Semi-Const. Current Method Rechargeable Battery 1.2V NiCd Zetex LED Driver LED 20mA 3.2V(min) Switching Control Mode Selection Photo Sensor Timer

22. Charge Controller Update Solar Panel I SC = 100mA V OC = 2.15V I AVE = 50mA Δt = 10hrs Q = 500mAHrs Charge Controller Semi-Const. Current Method Rechargeable Battery 1.2V NiCd Zetex LED Driver LED 20mA 3.2V(min) Switching Control Mode Selection Photo Sensor Timer