1. Transfering Trigger Data to USA15 V. Polychonakos, BNL

2. Introductory Comments  Huge advantage if trigger data transfer to USA15 logic can be implemented on the detectors  Harvard Scheme is fine  Adds complexity, cost, weight  Details needed, latency?  Can it run synchronously with BC clock?  Needs serializer  The need for serializer prompted us to change the ART output from parallel to serial LVDS. Gianluigi agrees, suggests scheme shown in next slide  The need for a custom digital ASIC triggered a reevaluation of the idea of direct on-detector transfer  Serial ART allows point to point connections avoiding a parallel bus (one of John’s objection to the scheme)

3. 25ns 50ns 75ns 100ns 125ns 150ns 175ns 200ns CK charge event analog pulse A peak-found FL D5 - D0 Assumes 160 MHz clock provided externally ART serialized in one line A Data D5-D0 shifted at each clock edge LVDS 600mV +/- 150mV VMM ART SERIALIZER - v2 reset

4. The transfer scheme in bullets  Point to point LVDS connections from the serial ART of 32 ICs (one layer of a “panel”) to a mezzanine board at the middle of the chamber (or perhaps part of a MMFE – average length of copper connections ~few cm)  Custom digital IC connected to a GBT operating in parallel mode (40 bit bus at 80 MHz transfers 80 bits in 25 ns)  For a given BC (the event BC) the flags of all ART signals arrive within the 25 ns of the event BC  Clocked by the rising edge of the next BC synchronizes the flags while some serial streams will finish arriving in the next bunch crossing  In the next to the event BC a priority encoding scheme or smart token builds a list of up to 6 hit addresses  A state machine operates on this list in the next BC and transfers them to the GBT at 80 MHz  Each 40 bit word contains up to 3 ART addresses (33 bits) plus 6 bits of the 12 bit BCID, high order in the first 40 bit word, low order in the second  Note that the ART in a given BC will be inactive in the next BC all others in the 32 IC group are active (we impose a dead time of a few BC any way)  Total latency is 2 BC clock ticks  GBT in parallel mode adds 5 BC ticks (2 seraliser, 3 deserialiser)

5. High Level Block Diagram GBT also provides the 80, 160 and, if needed, the 320 MHz Clocks

6. Overall Block diagram of the Digital IC

7. BCID/ARTA12 – 11 bitsA5 – 11 bits A2 – 11 bits BCID/ARTempty A16 – 11 bits DOUT[39:0] DOUT[79:40] VMM 0, STRIP 0 “000....00000” BCID/ART B.. DOUT[39:0]..CID/ARTART-6bits empty DOUT[79:40] 32-bit hit list 25 12 16 An alternative way (suggested by Sorin) to transmit the ARTs (Eliminates ambiguity with address 00)

8. A Possible implementation of the address transfer (WEN) (EN)

9. Timing Diagram of the Address Transfer Logic

10. Group ICs from the four layers of a multilayer (4 8-chip MMFEs) Trigger Board Possible location minimizes lvds lines to few cm, with adjacent group can use dual versatile link Front end boards

11. What’s next?  Scheme needs to be scrutinized for errors, wrong assumptions, etc  A Flag priority encoding or other scheme to identify up to 6 ART addresses (needs to be done in 25 ns, but maybe not if more than one BC of dead time is imposed )  Then write VHDL code and implement it on FPGA  Can have such a prototype by the time of VMM2  If convinced it works transfer the code to a custom design