1. NLA-5 Series Rigging Manual 2015.12.01.

2. Preparation Material 2

3. ㄴ Preparation Material- 1 3 1.Chain block or Electric hoist 2.Shackle (over 5/8 inch) 3.Sling belt 1 2 3

4. ㄴ Preparation Material - 2 4 1.FRONT BAR 2.BACK BAR 3.Bolt, Spring washer, Flat washer 3 2 1 4.Bolt & Washer Assembly (Must use 2 washers) 4

5. ㄴ Preparation Material - 3 5 21 1. Short bar is Back bar when connect Frame → NLA-15S NLA-15S → NLA-5. 2. Long bar is Back bar when connect NLA-5 → NLA-5.

6. ㄴ Preparation Material - 4 6 1.Shackle (1/2 inch) 1EA 1

7. ㄴ Preparation Material - 5 7 1.Electric Screw Driver 2.Hexagonal Tip (5mm) 3.Hexagonal Wrench_Manual (5mm) 1 2 3

8. Chain block Connection 8

9. ㄴ Chainblock Connection - 1 9 Like the above picture, connect a sling belt to a truss. (When you install it to H-beam, lower circled 1 to down side.) 1

10. ㄴ Chainblock Connection - 2 10 Like the picture, assemble the sling belt hanger to the shackle.

11. ㄴ Chainblock Connection - 3 11 Connected sling belt and shackle

12. ㄴ Chainblock Connection - 4 12 Connect hanger of chain block(or hoist) to shackle.

13. ㄴ Chainblock Connection - 5 13 Connected chain block / hoist

14. Frame Assembly 14

15. ㄴ Frame Assembly - 1 15 1.NLA-15S 2.NLA-5 FRAME 2 1

16. ㄴ Frame Assembly - 2 16 Put NLA-5 FRAME on NLA-15S.

17. ㄴ Frame Assembly - 3 17 Tighten up and down holes in FRONT BAR with bolts.

18. ㄴ Frame Assembly - 4 18 Adjust frame to make an alignment of middle hole and the screw hole in the frame.(1) 1

19. ㄴ Frame Assembly - 5 19 Tighten them with a bolt. (Use an electric screw driver for your convenience)

20. ㄴ Frame Assembly - 6 20 Connect rear side of the frame using short back bar.

21. ㄴ Frame Assembly - 7 21 Tighten whole points using manual hexagonal wrench.

22. ㄴ 프레임 조립 - 8 22 Connected frame on NLA-15S

23. ㄴ Frame Assembly - 9 23 Install ½ inch shackle to a preferred spot.

24. ㄴ Frame Assembly - 10 24 Connect the shackle to the hanger of chain block(or hoist).

25. NLA-5 Assembly 25

26. ㄴ Speaker Assembly- 1 26 Lift up frame(1) with chain block, and put one NLA-5(2) under the frame. 1 2

27. ㄴ Speaker Assembly - 2 27 Align front part of the speakers by lowering the frame.

28. ㄴ Speaker Assembly - 3 28 Firstly, tighten the up and down holes of FRONT BAR with bolts.

29. ㄴ Speaker Assembly - 4 29 Match middle hole in the bar and the speaker by adjusting position of them.

30. ㄴ Speaker Assembly - 5 30 Tighten the middle hole with bolts.

31. ㄴ Speaker Assembly - 6 31 Connect the lower part of short back bar with bolts.

32. ㄴ Speaker Assembly - 7 32 Lift up the speaker with chain block, and match up hole with speaker’s hole.

33. ㄴ Speaker Assembly - 8 33 Connect the up hole with a bolt.

34. ㄴ Speaker Assembly - 9 34 Completed 1 set of NLA-5

35. ㄴ Speaker Assembly - 10 35 Put another NLA-5 below.

36. ㄴ Speaker Assembly - 11 36 Align front part of NLA-5 using chain block.

37. ㄴ Speaker Assembly - 12 37 Connect the up and down hole in the FRONT BAR with bolts.

38. ㄴ Speaker Assembly - 13 38 Match middle hole in the bar and the speaker by adjusting position of them.

39. ㄴ Speaker Assembly - 14 39 Tighten the middle hole with bolts.

40. ㄴ Speaker Assembly - 15 40 Connect the downside of the long back bar with bolts.

41. ㄴ Speaker Assembly - 16 41 Rear part of NLA-5 5 0 10 Angles for each hole

42. ㄴ Speaker Assembly - 17 42 You can see that this picture is set to 0 degree. 5 0 10

43. ㄴ Speaker Assembly - 18 43 Choose your preferred angle of hole using chain block. The example in the photo is 0 degree.

44. ㄴ Speaker Assembly - 19 44 Connect it with a bolt.

45. ㄴ Speaker Assembly - 20 45 Completed 2 set of NLA-5

46. ㄴ Speaker Assembly - 21 46 Fully completed figure after repeated process.

47. NLA-5 RACK Assembly 47

48. ㄴ Speaker Assembly- 1 48 Insert an amplifier to NLA-5 RACK.

49. ㄴ Speaker Assembly - 2 49 1.Fill up spaces with blank panel. 2.Connect power cable, speaker cable, and LAN cable beforehand.

50. ㄴ Speaker Assembly - 3 50 Put NLA-5 FRAME on NLA-5 Rack.

51. ㄴ Speaker Assembly - 4 51 Tighten up and down holes in FRONT BAR with bolts.

52. ㄴ Speaker Assembly - 5 52 Adjust frame to make an alignment of middle hole and the screw hole in the frame.(1) 1

53. ㄴ Speaker Assembly - 6 53 Tighten them with a bolt. (Use an electric screw driver for your convenience)

54. ㄴ Speaker Assembly - 7 54 Connect rear side of the frame using short back bar.

55. ㄴ Speaker Assembly - 8 55 Tighten whole points using manual hexagonal wrench.

56. ㄴ Speaker Assembly - 9 56 Connected frame on NLA-5 RACK

57. ㄴ Speaker Assembly - 10 57 Put NLA-15S under NLA-5 RACK.

58. ㄴ Speaker Assembly - 11 58 Tighten up and down holes in FRONT BAR with bolts.

59. ㄴ Speaker Assembly - 12 59 Connect the middle with a bolt.

60. ㄴ Speaker Assembly - 13 60 Connect the lower part of short back bar with bolts.

61. ㄴ Speaker Assembly - 14 61 Connect the up hole with a bolt.

62. ㄴ Speaker Assembly - 15 62 Put one NLA-5 below, and tighten the up and down holes of FRONT BAR with bolts.

63. ㄴ Speaker Assembly - 16 63 Match middle hole in the bar and the speaker by adjusting position of them.

64. ㄴ Speaker Assembly - 17 64 Tighten the middle hole with bolts.

65. ㄴ Speaker Assembly - 18 65 Connect the downside of the short back bar with bolts.

66. ㄴ Speaker Assembly - 19 66 Lift up the speaker with chain block, and match up hole with speaker’s hole.

67. ㄴ Speaker Assembly - 20 67 Connect the up hole with a bolt.

68. ㄴ Speaker Assembly - 21 68 Completed 1 set of NLA-5

69. ㄴ Speaker Assembly - 22 69 Put another NLA-5 below.

70. ㄴ Speaker Assembly - 23 70 Align front part of NLA-5 using chain block.

71. ㄴ Speaker Assembly - 24 71 Connect the up and down hole in the FRONT BAR with bolts.

72. ㄴ Speaker Assembly - 25 72 Match middle hole in the bar and the speaker by adjusting position of them.

73. ㄴ Speaker Assembly - 26 73 Tighten the middle hole with bolts.

74. ㄴ Speaker Assembly - 27 74 Connect the downside of the long back bar with bolts.

75. ㄴ Speaker Assembly - 28 75 Rear part of NLA-5 5 0 10 Angles for each hole

76. ㄴ Speaker Assembly - 29 76 You can see that this picture is set to 0 degree. 5 0 10

77. ㄴ Speaker Assembly - 30 77 Choose your preferred angle of hole using chain block. The example in the photo is 0 degree.

78. ㄴ Speaker Assembly - 31 78 Connect it with a bolt.

79. ㄴ Speaker Assembly - 32 79 Completed 2 set of NLA-5

80. ㄴ Speaker Assembly - 33 80 Fully completed figure after repeated process.

81. Caution 81

82. ㄴ Caution 82 1.You should insert spring washer and flat washer for your bolts. 2.THREE holes in the front part of the speaker must be connected with bolts. (Connecting only 2 holes(up&down) might cause a problem) 3.Position for shackle connecting to the frame is up to user’s preference.

83. ㄴ Caution 83 4.For tightening bolts, electric screw driver is more convenient and safe than manual hexagonal wrench. 5.When you use electric screw driver, it is recommended to use slow motor speed. (Fast motor speed easily makes a crooked bolt) 6.For your safety and convenience, you have to tighten bolts with manual hexagonal wrench after you use electric screw driver.