1. AMS-02 tracker mechanics status of construction, assembly, integration Ladder assembly Ladder installation on planes Integration details, cooling loop, star tracker Safety issues Tracker assembly Schedule Divic RAPIN, UniGe Summary of contributions from: M. Paniccia, M. Ionica, F. Da Silva, E. Perrin, B. Verlaat, C. Gargulio

2. General view of Silicon tracker 5 planes, 8 layers Plane 1, layer 1 Plane 2, layers 2&3 Plane 3, layers 4&5 Plane 4, layers 6&7 Plane 5, layer 8 192 ladder modules

3. Ladder Assembly Status (Perugia-Geneva) ASSEMBLY ~ 200 ladders build 1 ladder still to be assembled 4 ladders to be repaired PHASE 2 hybrid box & legs gluing ~ 7 ready for process EMI SHIELDING ( kapton foil wrapping) ~ 38 ready for processs Full test at each step with RA source and noise control

4. Installation of ladders on support planes Ladders are installed on both sides of the 3 inner planes. 5 over 6 layers are fully equipped with ladders Inner part of the tracker soon completed. Ladders on plane 4

5. Installation of ladders on support planes Plane 3 being stored (under Nitrogen) Details of fixation on both sides

6. AMS-02 Tracker - Plane 2 July 21, 2005 Ready To be Integrate Integrated L07PI002 L09GI006 L14AI031 L09GI003 L10PI005 L10GI014 L11GI004 L11GI009 L11GI016 L09GI013 L09GI010 L14AI042 L07PI004 L11GI008 L12AI001 L12AI004 L12AI006 L12AI003 L12AI005 L12AH024 L12AH057 L12AH029 L12AJ021 L12AJ051 L10PI008 L14AI044 L12AJ054 L12AJ055 L10PI001 L09GI002 L11AI126 L11AI140 L12AJ033 L11SI176 L12SH169 L12AH058 L14AI032 L09AI139 L09GI011 L11AI127 L09SI164 L12AI012 L12SI167 L12AJ038 L12SI182 L12AI016 Before phase 2 at Perugia Last inner layer close to completion

7. Installation of ladders on support planes Thermal bars installed on external planes

8. AMS-02 Tracker - Plane 5 July 19, 2005 ON PHASE-2 READY TO BE SHIELDED ASSEMBLY COMPLETED L10AO144 L15AN117 L12AO105 L10AO147 L14AO119 L13AO074 L13AO073 L15AP112 L15AP098 L15AP110 L15AN118 L14AO120 L15AO093 L15AO097 L15AO095 L14AO122 L14AO124 L13AO111 L12AO106 L10AO148 L10AO145 L14AO157 L14AO121 L13AO072 L11AO155 L15AO116 L15AO162 L15AO115 L15AO096 L11SO165

9. AMS-02 Tracker - Plane 1 July 21, 2005 ON PHASE-2 READY TO BE SHIELDED ASSEMBLY COMPLETED L12AO107 L15AN100 L15AN101 L13AO114 L15AN113 L10AO146 L10AO150 L13AO025 L14AO160 L15AP099 L15AP109 L13AO026 L14AO158 L15AO173 L15AO174 L15AO175 L13AO071 L14AO159 L14AO156 L14AO123 L14AO125 L15AO163 L11AO153 L10AO151 L10AO149 L12SO181 L15SO180 L15AO17 7 L11AO15 4 L15SO178 ON PRODUCTION STAND BY ON REPARATION

10. TTCS Evaporator Production Status B. Verlaat & M. Van Overbeek NIKHEF, 14 October 2005

11. Evaporator is split with hydraulic connectors Inner ring Outer ring Intermediate Connectors In & Outlet Connectors

12. July 2005: 2 Inner rings are produced!

13. Inner ring under production Bending tool details Soldering set-up

14. Inner ring production results Copper block details Complete inner ring

15. Outer Ring Assembly and soldering jig Outer Ring Details Outer ring under production

16. Evaporator clamps in Tracker structure Inlet and outlet tube clamp Inner ring central clamp

17. 1) Bolt analysis was made by ISAtec and A.Alvino. ==> We need better quality bolts for some cases: One junction (tracker feet  tracker) deserves more attention and will be discussed on Wednesday splinter meeting. 2) Tracker fastener list and back off prevention method: Submitted to Jacobs. Update needed for structural fasteners. Back-off prevention clear - Two cases: i) Contained small fasteners : Vibratite ii) Other fasteners: Mylar patch or self locking insert 3) Fracture of composites: Memo submitted to Jacobs. 4) Material list: Delivered to Jacobs Some issues: - Some Al alloy plates to be surface treated in-situ - A few components are prone to stress corrosion Safety issues

18. Dry assembly of shells-planes was made before installation of ladders on planes. …it continues with the new conical flange and the external planes… Tracker assembly at Uni-GE

19. Dry assembly continues: - Star tracker lower support to upper conical flange. - P1 to top conical flange - P5 to bottom conical flange. - Spl brackets for evaporators

20. Dry assembly continues: -Star tracker lower support to upper conical flange. -Two pieces of the camera support to upper plane and upper flange

21. Assembly of the inner tracker at UniGe Proposed set-up for storage & insertion into the magnet. The various lengths of the cables were calculated. Cables are in UniGe Cables must be installed before the supporting shells. Extra length must be attached to temporary supports.

22. Tracker assembly at Uni-GE Modifications can start: - Remove / reposition telescopic supports for inner planes. - Build adapters for conical flanges - Define plane transfer method ==> By hand ? ==> With a lifter ? The ETHZ Frankenstein machine has been moved to UniGe

23. Assembly schedule Inner Tracker assembly can start as soon as : - The three inner planes are ready for assembly  ~End of November Delayed because of a missing ladder - The modifications to Conical flanges / Shell are made (if needed) - The Star Tracker lower supports are bonded to the top conical flange - The fasteners are available Assembly sequence - Transfer the 3 inner planes into the « Frankenstein » in order P2, P3 and P4 - Transfer the conical flanges into the « Frankenstein » - Position planes and connect thermal connectors - Mount cable support structure - Mount and connect cables on ladders of three external rows +Y and -Y - Mount the two 100° shell sectors - Mount and connect all other cables - Mount the two 80° shell sectors Inner Tracker assembly ==> Duration ~2.5 months ~End February2006 if assy starts early December

24. P5 completed with ladders  ~Mid February 2006 P1 completed with ladders  ~End of March 2006 (Test are not accounted for ) Still a lot of things to finalize / to do for the assembly of the Inner Tracker: - Procure fasteners which need to be replaced - Shopping list for next TIM - Light tightness at exit of conical flange / around the feets - Mesh on light traps - Bond Star tracker lower support - Cable clamps - Structure to support cables - Container for Inner Tracker. - Etc...

25. Further assembly steps / parts needed - Re-do some bracketry for evaporators in two parts - Mount outer evaporator rings to P1 and P5 - Modify outer plane containers to be compatible with evaporators For integration - Inner Tracker handling gear - Installation jig for Inner evaporator (design A. Alvino) - Cable « paddle » and clamps on Vacuum case (design A. Alvino) - Cable balcony for Tracker crates. Miscellaneous - Prototype condenser - Parts for heat exchanger