1. NZR Full slider c/w extended A/F

2. 5 th wheel Slider Truck/Tractor D-train – Min. FA/AF 230” 29’ 3” (Max 32’ 9”) D-Train Configuration Typical Day Cab Tractor Specs F/A 50” A/F 71” 113”

3. D-Train Configuration Typical Day Cab Tractor Specs 16 foot slider for 5 th wheel mounted over tractor frame

4. D-Train Configuration Typical Day Cab Tractor Specs

5. NZR D-train Hitch System

6. A Closer Look at the “D” Connection

7. NZR Patented D-Train Hitching System View from the Top Down – The “Rigid” Connection 1.Tractor has just backed into the kingpin of the trailer and by nudging forward has already exposed the “B-Train” for connection to the second trailer ( a single axle trailer and an “A-Train converter dolly connection is optional) 2.Have ignored the landing gear for simplicity of demonstration 3.The tractor-facing end of the trailer bogie is equipped with a unique after-frame pocket assembly which has entrance guides on each side. The after-frame of the tractor will typically tuck inside the trailer D-Train pocket about 11 – 12 inches. This depth is managed by allowing the fifth wheel to be pushed or pulled to complete a proper connection.

8. 28.5 foot lead trailer D-Train System The D-Train Connection Mk V 2 Speed Landing Gear Mk V Sliding Rail & Lock Sliding “B-train” bogie Kingpin 18” S/B

9. 28.5 foot lead trailer D-Train Configuration Coupling Demonstration

10. 28.5 foot lead trailer D-Train Configuration Coupling Demonstration D-Train Trailer After Frame Kit

11. 28.5 foot lead trailer D-Train Configuration Coupling Demonstration D-Train Trailer After Frame Kit

12. 28.5 foot lead trailer D-Train Configuration Coupling Demonstration Sliding “B-Train” Bogie is unlocked and tractor edges forward to expose the 5 th wheel Steering Axle

13. 28.5/32 foot lead trailer 35/53 foot pup trailer D-Train Configuration Coupling Demonstration

14. 28.5/32 foot lead trailer 35/53 foot pup trailer D-Train Configuration Coupling Demonstration Pup Landing Gear Raised – Configuration Ready to Go!

15. 53 foot standard trailer 4 ‘ Incremental payload – Gap closure 6.5 ‘ Additional Cargo Space Regulated Maximum Combined Box Length – 65’ 7” (20 meters) Net Cargo Length Advantage – 10.5 feet 2 ‘ 2” Lead-Pup Gap D-Train Configuration Increases Payload 20% (10.5/53) Out-Performing the 53’ Standard Trailer

16. D-Train System Advantages of the D-Train versus a Standard 53 Foot Trailer 28.5/32 foot trailer 35/53 foot pup trailer 53 foot standard trailer 4 ‘ Incremental payload – Gap closure 6.5 ‘ Additional Cargo Space Regulated Maximum Combined Box Length – 65’ 7” (20 meters)

17. 28.5/32 foot trailer 35/53 foot pup trailer 53 foot standard trailer 2 ‘ 2” Lead-Pup Gap Plus an Additional 6.5 ‘of Cargo Space Net Cargo Length Advantage – 10.5 feet D-Train System Advantages of the D-Train versus a Standard 53 Foot Trailer 4 ‘ Incremental payload – Gap closure D-Train Configuration Increases Payload 20% (10.5/53) Regulated Maximum Combined Box Length – 65’ 7” (20 meters)

18. D-Train System Turning Radius Advantage of the D-Train versus a Standard 53 Foot Trailer

19. D-Train System Turning Radius Advantage of the D-Train versus a Standard 53 Foot Trailer

20. Tractor-Trailer “GAP” A Major Drain on Fuel Consumption At 50 mph the energy consumed to overcome aerodynamic drag starts to exceed that required to overcome rolling friction and drive train losses Source: SAE International Aerodynamic Drag Reduction Studies, 2003

21. Tractor-Trailer “GAP” A Major Drain on Fuel Consumption Source: SAE International Aerodynamic Drag Reduction Studies, 2003 “Gaps” vary but because of the articulating trailer, the gap is a minimum of 4.5 feet and often exceeds this in many configurations

22. In zero crosswinds, studies show up to 50% reduction in drag coefficient with the application of fairings and roof- top air deflectors Tractor Fairings and Air Deflectors Help Source: SAE International Aerodynamic Drag Reduction Studies, 2003

23. Tractor Fairings and Air Deflectors Help But... In crosswinds, these benefits are cut in half Source: SAE International Aerodynamic Drag Reduction Studies, 2003 Total rig drag is 0.75 In zero crosswinds, studies show up to 50% reduction in drag coefficient with the application of fairings and roof- top air deflectors

24. Tractor-Trailer “GAP” The D-Train Configuration Reduces “Drag”, Which Reduces Fuel Consumption Source: SAE International Aerodynamic Drag Reduction Studies, 2003 Total baseline drag in crosswinds for a T-T combination approximates a CD of 0.75. Closing the “Gap” from an average of 4.5 feet to just 6 inches, results in 44% (2/4.5 - note adjustment for addition of 2 feet between lead and pup units) reduction in drag derived from these connections or CD measure reduction of.066 (44% x.15) – overall an 8.8% (.066/.75) reduction in total rig drag. At 60 mph that yields fuel savings of 4.4% (8.8%/2% see table) and the higher the speed the greater the savings A D-Train configuration closes the tractor trailer “gap” to as little as 6 inches.

25. Total baseline drag in crosswinds for a T-T combination approximates a CD of 0.75. Closing the “Gap” from an average of 4.5 feet to just 6 inches, results in 44% (2/4.5 - note adjustment for addition of 2 feet between lead and pup units) reduction in drag derived from these connections or CD measure reduction of.066 (44% x.15) – overall an 8.8% (.066/.75) reduction in total rig drag. At 60 mph that yields fuel savings of 4.4% (8.8%/2% see table) and the higher the speed the greater the savings Source: SAE International Aerodynamic Drag Reduction Studies, 2003 NOTE that with integrated fairings design, it is possible to eliminate all effects of tractor-trailer gap – fairings could completely encase the head of the trailer since it is rigidly attached to the tractor Tractor-Trailer “GAP” The D-Train Configuration Reduces Fuel Consumption

26. Fleet Targets – Selection CriteriaElaboration 1.Type and size of equipment fleet Priorities: Dry vans, 53’ trailers Dump truck fleets Refrigerated vans, 53’ trailers 2.Magnitude and scope of short-term benefits possible Typically reflected in direct costs such as lower fuel, lower wages and reduced owner-operator costs on a per kilometer/mile basis 3.Magnitude and scope of long-term benefits Typically reflected in lower capital invested per revenue mile/kilometer earned or greater revenue per mile/kilometer for the same capital invested; or greater customer satisfaction 4.Ability to commit financial capital for fleet investments How much and how fast? 5.Complexity of the buying process Bureaucracy – paperwork – approval levels? 6.Level of motivation of the economic decision-maker Who is the ultimate financial decision-maker? 7.Decision-making influence of other stakeholders The owner operators, the drivers, the maintenance staff 8.Willingness to share internal information and “partner” with us Will they open up and let us show how our solutions could help them? 9.Ability to plausibly quantify benefits Hard evidence that the new technologies deliver real value 10.Proximity to our installation and service locations Toronto initially, expands from there

27. Maximum Box Length 65’ 7” Ontario LCV Limits Maximum Combination Length 82’ Max 16’ 5” Ontario and the rest of the provinces limit the combined trailer length to 65’ 7 “ for B and C-Train combinations ( 60.7 feet for A-Train combinations) In the USA it varies by state, for example, Oregon limits doubles trailer lengths to 60’ in general and 68 feet on designated highways. South Dakota, on the other hand, permits trailer combinations as long as 81.5 feet for a 2 trailer rig. Some pertinent points for Ontario: 1.Trailer box lengths for the D-Train – These two units ought not be built in equal sizes (ie., each say 31.5 or 30). Doing so would not enhance their combined ability to handle more whole skids, assumed for the most part to equal 4x4 in dimension. A solution is to build one unit say 28.5 and the second unit 35. With a 2 foot allowance for “gap” that creates a combined length of 65.5. This combined capacity can load 60 skids per layer versus 52 in a 53 foot semi-trailer, a 15.4% improvement in skid loads per trip. 2.Optimizing to the regulated combined box length results in there being 16’ 3” feet left for a tractor unit to be hooked rigidly to the lead trailer unit. A day cab unit would require only about 9’10” to 10’. At 16’ 5” there is sufficient space to support all forms of sleepers for TL linehaul work.