2. Writing for CE 314K How to get lab experiences and results into a written document? Spring 2002

3. Dr. Hillary Hart www.ce.utexas.edu/prof/hart/manual/index.htm Office Hours -- ECJ 8.214 MW 11:00-12:00Th 3:00-5:00 471-4635 hart@mail.utexas.edu TAs – ECJ 3.256B Rebecca BennettT 3:45-5:15 Kenny MillerT 11:30- 1:00 Th 11:00-12:30

4. Organization of a Lab Report Title page Table of Contents (if more than 4 pp) Introduction –Background Test Procedure Results and Discussion Conclusions Appendices

5. Introduction State purpose of lab and purpose of report Provide basic definitions Provide background information –include basic equations –use subheading Background

6. Test Procedure Briefly describe testing procedure Refer to detailed procedure in appendix Discuss changes or deviations from established procedure

7. Results and Discussion Present results in figures and tables –Use titles and labels – see next slide. Tell the story of what happened, weaving in figures and tables. Analyze and interpret the results Compare the results with theory –did the expected happen? Organize results to illustrate main points

8. Guidelines for Integrating Graphics with Text Position each graphic as near as possible to the narrative it supports. Comment on every graphic at least once in the text. Discuss significance!

9. Guidelines for Labeling  Label each graphic clearly with a figure or table number and a title.  Place the figure number and title beneath a figure (graph, chart, etc.).  Place the table number and title above a table.  Create a title (or a title and a caption) that draws attention to significant aspects of the graphic.

10. Conclusions Restate most important findings Describe relevance of findings and their application to engineering problem-solving Do NOT introduce new information

11. Appendices Give each appendix a letter and a title Number pages separately from report –e.g., A-1 Include detailed information: –Data sheets, sample calculations, mathematical derivations... anything not essential for a reader’s understanding of the report. Include a References section Cite each appendix in body of report

12. Read Requirements! All the information on “Required Organization of Lab Reports” applies to your writing over the course of this semester. The “Other Requirements” apply directly to all of your writing assignments.

13. Passive VoiceActive Voice l Elapsed time is indicated by a pointer. l A pointer indicates elapsed time. The project was completed by the installation crew. It is suggested that readings be recorded hourly. l The installation crew completed the project. I suggest you record readings hourly.

14. When to use which? to emphasize the agent of the action: Previous researchers established the relationship between chemical qualities and model parameters. Active VoicePassive Voice to emphasize the object: The relationship between chemical qualities and model parameters was established by previous researchers. The water sample was heated to a temperature of 100 0 C. to be concise and direct: JMC Consulting recommends that BPAmoco adopt a risk-communication plan

15. Passive voice is the easiest way to avoid saying “I” or “we:” –The data were reduced by averaging two dial-gage readings. But it’s not the only way: Averaging the two dial-gage readings reduced the data. When passive voice makes a more straightforward sentence, use it! Otherwise, strive to use active.

16. Where to use which? Passive – to explain what you did: Procedures –The data were reduced by averaging two dial- gage readings. Active – to state theory or conclusions: Discussion of Results and Conclusions –As a result of its anisotropic structure, the elastic limit of wood is relatively low.

17. Using Topic Sentences Once concrete has been mixed and allowed to cure, various test can be performed to determine if the concrete meets desired strength specifications... –paragraph describes destructive and nondestructive testing methods Sentence provides good transition from previous paragraph (on concrete mixing).

18. Providing transitions between sentences Slump tests determine the consistency of concrete. A low slump indicates a stiff mixture. The desired slump is between 3 and 4 inches. –Choppy! The consistency of concrete is determined by slump tests, in which a low slump indicates a stiff mixture. The desired slump for this experiment is between 3 and 4 inches. –Improved

19. Streamlining: Removing the Dead Wood The following report outlines the different aspects relating to the current feasibility of constructing a magnetically levitated bullet train in Central Texas.