1. XAS 375 JD6 Compressors Scott Ellinger
Committed to sustainable productivity

2. Technical Specifications - XAS 375 JD6

3. Technical Specifications - XAS 375 JD6 (2)

4. Technical Specifications - XAS 375 JD6 (3)

5. Flow summary XAS 375 JD6

6. AIR SYSTEM INLET VALVE Spring loaded in the ready position
Control Air closes the inlet
Also serves as check valve

7. No-Load Condition Load Condition

8. Unload Condition Blow- Down Condition

9. REGULATING VALVE
Spring loaded
Adjusting receiver pressure
by changing spring tension
to pressure gauge and loading valve
to speed regulator
to unloading valve
Regulating pressure:
Receiver pressure
In order to regulate the pressure inside the reciever tank of our compressor, the air intake and the engine speed have to be controlled. This is done pneumatically. For that reason, we need regulating pressure. The regulating valve reduces the pressure inside the tank, thus providing the regulating pressure. This regulating pressure is then supplied to the unloader valve and the speed regulator or RPS.
The air receiver pressure can be set to another value by adjusting the spring tension of the regulating valve. This is done by turning the handle on top the valve. Increasing the spring tension, by turning in, will increase the regulating pressure and consequently the pressure inside the vessel. Turning out will decrease the pressure.

10. AIR SYSTEM MINIMUM PRESSURE VALVE
Maintains a minimum pressure
of 58 PSI for oil flow
Also contains the final check
valve

11. Control Panel

12. XC 2002 Controller

13. XC2002 Controller Overview

14. XC 2002 Control Module

15. XC 2002 - Menus *Password is 2003*
On newer units Parameters are under Extra Views.
*Password is 2003*

16. XC 2002 Controller – 1.200 Program

17. XC 2002 Controller – 1.200 Program
Automatically loads “with use of in line micro switch”
Automatically unloads unit “unit will not reload”
Service Timer 1 = 500hrs
Service Timer 2 = 1000hrs
“On” lets you connect to engine with machine not running

18. XC 2002 Controller – 1.200 Program

19. XC 2002 Controller – 1.200 Program

20. XC 2002 Controller – 1.200 Program

21. XC 2002 Controller – 1.200 Program – Unit Type 2

22. Event Logging

23. J1939 Canbus Engine Communication

24. XC2002 Service Timer Reset
Scroll through the controller menu to “Parameters” (on some units “Parameters” may be a submenu under “Extra Views”)
Press Enter to select Parameters
Scroll to ST1 Reset or ST2 Reset as needed (ST1 = 500 hours, ST2 = 1000 hours)
Press Enter to select to reset the appropriate timer
Center option will highlight; scroll to highlight “Yes” and press Enter
Change Password to 2003 and press Enter
Service timer is reset

25. Engine Fault Code List

26. Engine Fault Code List

27. Engine Fault Code List

28. Engine Fault Code List

29. Engine Fault Code List

30. Engine Fault Code List

31. Engine Fault Code List

32. Engine Fault Code List

33. Engine Fault Code List

34. Displaying of J1939 DM1 Alarms

35. Wiring Schematic – XAS 375 JD6
Canbus terminator resistor p/n

36. Legend

37. John Deere – Tier III – RPS in place of Pneumatic Speed Regulator
Regulating Pressure Sensor
“Speed Sensor”

38. Preheat Relay K1 Controlled by JDEC
Starter Relay

39. Preventive Maintenance Filter Kits – XAS 375 JD6

40. Spare Parts Recommendation

41. Contact Numbers Main Number Atlas Copco Technical Support
Option 3
Clayton Jones - Hurricane Boosters/Compressors - Supervisor
direct & mobile
Andrew Stevenson – Compressors: Low Pressure
direct & mobile
Will Hudson – Generators/Compressors
Ext & mobile
Andrew Calendar – Compressors: High Pressure
direct & mobile
Jon Monaco - Hydraulic Att./Handheld Tools
Ext & mobile
Brandon Dyer – Compressors: Low Pressure/Hydraulic Att.
direct & mobile
Scott Ellinger – Compressors
direct & mobile

42. Committed to sustainable productivity.