1. Roll up Door CHECK GEAR OIL CAPACITY MAINTAIN AT FILLER PLUG LEVEL
DIPSTICK FOR GEAR OIL
PLUG
GEAR OIL PLUG LOCATION
USE A 9/16” OPEN END WRENCH
GEAR OIL CAPACITY 12 FL. OZ. (GRADE 150)
CHECK GEAR OIL CAPACITY
MAINTAIN AT FILLER PLUG LEVEL

2. Roll up Door LUBRICATE CHAIN AS NEEDED.
WHEN CHAIN BECOMES DIRTY, WASH IN KEROSENE (DO NOT USE GASOLINE OR OTHER SOLVENTS), THEN LUBRICATE WITH A LIGHTWEIGHT MACHINE OIL. READJUST CHAIN FOR PROPER TENSION IF NECESSARY.

3. Roll up Door
CHECK ALL BOLTED CONNECTIONS, MAINTAIN CLEAN, TIGHT AND FREE OF CORROSION

4. Roll up Door
LUBRICATE SIDE GUIDES

5. Cord Reel
PULL OUT THE FULL LENGTH OF THE ELECTRICAL CORD REEL AND RETRACT THROUGH A CLEAN RAG LIBERALLY SOAKED WITH SILICONE LUBRICANT.

6. Cord Reel AIR SHUT-OFF VALVE SAFETY LATCH AIR REWIND MOTOR
REWIND CONTROL VALVE
INSPECT ALL ELECTRICAL COMPONENETS
INSPECT ALL MECHANICAL COMPONENETS

7. Manifolds
LUBRICATE 2 ZERK FITTINGS EACH OUTLET
ZERK FITTINGS

8. Camera Connections 1 4
Connect camera to outlets inside grey box in the Pedestal.
Turn Monitors on to channel 31.
Turn toggle switch on, Aft plenum toggle is #1 and Pedestal #4, check picture on all 3 Monitors.
Lubricate camera connections with Silicone.

9. Camera Connections
CHANNEL CONTROL
MONITOR “ON, OFF” 1 2 3
TOGGLE # 1
TOGGLE # 4
Connect camera to outlets inside grey box in aft plenum
Turn Monitors to channel 31.
Turn toggle switch on, Aft plenum toggle is #1 and Pedestal is # 4, check picture on all 3 monitors.
Lubricate camera connections with Silicone.

10. Electrical Outlets/Covers
LUBRICATE THREADS ON THE COVER
ZERK FITTINGS

11. Wire Rope
WIRE ROPE
INSPECT ENTIRE LENGTH OF WIRE ROPE. LUBRICATE AS NEEDED.
LEATHER GLOVES SHOULD BE USED WHEN HANDELING WIRE ROPE.
WHEN WINDING WINCH CABLE ON THE WINCH DRUM, NEVER ATTEMPT TO MAINTAIN TENSION BY ALLOWING WINCH CABLE TO SLIP THROUGH HANDS. ALWAYS USE “HAND-OVER-HAND” TECHNIQUE.
THE FORMATION OF KINKS MUST ALWAYS BE PREVENTED AS THIS DISPLACES THE STRANDS OF WIRE FROM THEIR ORIGINAL POSITION & RELATION TO EACH OTHER CAUSING SEVERE BENDING AND UNEQUAL TENSION IN THE STRANDS. THIS DISTORTION AND WIRE DISPLACEMENT CANNOT BE CORRECTED EVEN UNDER HIGH TENSION & A PERMANENT WEAK POINT REMAINS IN THE ROPE. DISPLACED OR RAISED WIRES INDICATE A PREVIOUS KINK, BUT WILL NOT SHOW THE DAMGED CONDITION OF THE INNER ROPE WIRES.

12. CRANE BOOM LUBRICATION
EXTEND CRANE FULLY CLEAN ALL FOUR SIDES WITH A DEGREASER BRUSH ON AMSOIL HEAVY DUTY SYNTHETIC GREASE ON ALL FOUR SIDES. USE POSITIONING PADS AS GUIDES FOR GREASE LINES.

13. CRANE LUBRICATION 1 2 EXTEND CRANE FULLY LUBRICATE ZERK FITTING
LUBRICATING PORT
EXTEND CRANE FULLY
LUBRICATE ZERK FITTING

14. Crane Basket Outlets MAKE CONNECTIONS TO SUPPLY CRANE BASKET OUTLETS.
SILICON CONNECTIONS
TEST OUTLETS
ZERK FITTINGS

15. Tow Reel LUBRICATE ZERK FITTINGS.
OPERATE REEL (PULL OUT ENTIRE LENGTH AND AIR REWIND.
ZERK FITTINGS

16. Bulwark & Deck House Lights
LUBRICATE THREADS WITH VASELINE.
CLEAN GLASS.
33 BULWARK LIGHTS.
ZERK FITTINGS

17. Rescue Platform
Wipe Zerk fitting clean with a red rag before lubricating.
Lubricate Zerk fittings on each side of Rescue Platform .
Zerk fittings

18. Flood Lights LUBRICATE METAL LATCHES. CLEAN INSIDE GLASS AS NEEDED.
ZERK FITTINGS