2. Rotational Mechanics

3. Rotational Motion Rotational Speed or Angular Speed Typically measured in rpm’s or degrees/sec, but the SI unit is radians/sec ω = Δ Θ / Time ??? What is the rotational speed of a clock’s “second” hand in rpms? Angular Acceleration: The rate of change in Angular speed α = Δ ω / Time

4. Rotational Motion VS Linear Motion The linear speed or tangential speed of an object depends on its radial distance. v = ω r Ex: The horses on a carousel all go around with the same angular speed, but the outside horses have a greater linear speed. ??? Suppose two cars have a race. Car A has 12 inch wheels that can rotate at 500 rpm. Car B has 24 inch wheels that can rotate at 400 rpm. Which car will win the race?

5. Measuring Angular Speed 1.Record the time it takes an object to roll down an incline 1 meter long. 2.Determine the diameter and circumference of the object. 3.Determine the number of rotations the object went through when it rolled 1 meter. 4.Determine the object’s average Angular Speed. (rotations/sec) 5.Determine the object’s final Angular Speed. (rotations/sec) 6.Determine the object’s angular acceleration. (rotations/sec 2 ) 7.What are some possible reasons why different objects rolled down at different rates?

6. Rotation Review A wheel starts at rest and then rolls 5 times down a hill in just 3 seconds. 1.What was its average angular speed in rotations/sec? 2.What was its final angular speed in rotations/sec? 3.What was its angular acceleration?

7. Buttered Cat Paradox

8. Warm-up 1. Where is the most exciting place to sit on a merry-go-round? Why? 2. If railroad wheels are on the same axle (same angular speed), how is it possible for trains to turn? 3. What should roll down a hill faster, a solid sphere, solid disk or hollow hoop (assume same mass)?

9. Rotational Inertia Introduction Observe the motion of a Ball, Solid Disk, and a Hoop rolling down an incline. Rotate the two different “inertia sticks” Observe the falling chimney. Definition: Rotational Inertia directly depends on the mass of a rotating object and on how far the mass is located from the axis of rotation. Other Examples: Tight rope walkers,FlyWheels, Running, Gymnasts

10. More rotation examples Ex. If you turn off your workshop grinder and electric drill at the same time, which one takes longer to come to a stop? (2 reasons) Ex. Why are little kids told to “choke up” on a baseball bat? Ex. Why do the front brakes wear out faster than the rear brakes on a car?

12. Torque Torques cause changes in rotation! Just as Forces cause accelerations. Torque = (Force) x (lever arm distance) –Ex: 100 Newtons of force is applied perpendicularly to a 0.5 meter wrench. –Remember: the perpendicular component of the applied force is what counts! –Ex: Torque Feeler, Torque wrench, Cheater Bar?

13. Torque examples Meter stick challenge (weighted and unweighted) Hammer See-saw Screwdriver—how would you modify the shape to maximize torque?

14. Center of Mass / Center of Gravity Center of Mass (Gravity) is the average position of all the mass (weight) that comprises an object (balance point). Ex: Where is the CM of a ball located? Ex: Where is the CM of a hollow disc located? Ex: Where is the CM of a hammer located? For freely rotating objects; they will rotate around their CM. Baton twirling, rifles Baby in-utero Earth-moon system—why does the Earth wobble?

15. Earth/MoonSun/Earth

16. Stability An object is stable if the sum of the torques acting on it equal zero (cancel each other out) –Ex: A 2 kg mass is suspended from the 10 cm mark of a meter stick. Where can a 5 kg mass be placed on the meter stick so that it is balanced about the 50 cm mark? You can also consider objects to be stable if their CM is located directly above or beneath an area of support. Ex: Tower of Pisa, Heel/Toes against the wall, Chair/Head/Wall pick up Freshmen! Pregnant women!

17. Stability – Check Questions 1.What is the torque caused by a 250 N force applied at the end of a 40 cm wrench? 2.A 5 kg mass is suspended from the 5 cm mark of a meter stick. Where can a 8 kg mass be placed on the meter stick so that it is balanced about the 50 cm mark?

18. Centripetal Force and Acceleration Centripetal Force is a force exerted on an object that causes it to change direction. It is always directed towards the center of curvature. –a c = v 2 /r –F c = mv 2 /r –Centrifugal Force is the reaction force. –Ex: A 0.1 kg ball twirled around by a string at a constant 5 m/s. –What is the centripetal acceleration? –What is the centripetal force on it? –Distinguish the centripetal force from the centrifugal force.

19. What On Earth is Spin? http://www.youtube.com/watch?v=H4JU TnkiGpI&edufilter=8gyTAQpnAaFW N9xxR7pk4A&safe=active

20. Simulated Gravity By rotating a space station, inhabitants will be forced to move in a circular path and experience a centripetal force – much like gravity. However the space station will most likely be large to overcome dizzying effects and varying amounts of Centripetal Force Ex’s: 2001, 2010, Mission Mars, Armageddon Armageddon

21. Review 1.What is the weight of the above meter stick shown above? 2.What is the centripetal acceleration of a space station that is 20 meters in radius and rotating at 10 m/s? 10 N 20 cm 0 cm100 cm

22. Angular Momentum Conservation Angular Momentum is Rotational Inertia IN MOTION! –L = I  Conservation of Angular Momentum: –In the absence of net torque, the total angular momentum of a system is conserved. Ex’s –Spinning stool and tire, Ice Skater, Gymnast, Earth’s rotation, Comets in orbit. Helicopters…

23. XKCD fans?

24. What allows cats to flip over and ALWAYS land on their feet?!? (video)

25. Helicopters Tail Rotor prevents the helicopter from spinning out of control. Why don’t these have tail rotors?

26. Precession If there is an outside torque acting on a system, then the angular momentum will change. Ex: Hanging bike tire, Earth’s precession (~26,000 yrs), Spinning Top