1. New sliding gates gearmotor C720 24V

2. Summary  Why a 24V operator?  USPs  Technical specifications

3. Why a 24V gearmotor ? Gain shares in the growing market of 24V sliding gates operators 

4. The FAAC solution

5. Summary  Why a 24V operator?  USPs  Technical specifications

6. Strong points New Cyclo gearbox (FAAC international patented) New integrated control board (E720) New design 1 3 2

7. C720 28 Teeth Pinion 24 m/min Battery Backup Package (optional) Magnetic Limit Switches Easy Release Handle Built-in 24Vdc Electronic Board with: Bus Technology, Obstacle Detection, Omnidec Receiver

8. Cyclo gearbox Eccentric shaft Impellers Ball bearing Slow speed gear How does it work?

9. As the eccentric shaft rotates, it rolls the impellers around the internal circumference of the slow speed gear. The resulting action is similar to that of a wheel rolling around the inside of a ring. Since the impellers are fixed, this imposes a movement of the slow speed gear. Eccentric shaft Impellers Ball bearing Slow speed gear Cyclo gearbox

11. Which are the advantages?  High mechanical efficiency: Higher than 80% (+50% compared to the traditional gearboxes )  Robustness and reliability: the load is distributed to many contact points  Vibration and noise reduction: the impellers are 180°out of phase, making the gearbox perfectly symmetrical and equilibrated  Dimension reduction: the whole gearbox is contained in the slow speed gear, which is directly connected to the gate rack Cyclo gearbox

12. High mechanical efficiency Cyclo gearbox Lower power consumption means lower heat dissipation: better operating conditions for the mechanical components (motor, gearbox, etc.) that means a longer lifetime of them. x2 Higher thrust force and speed (up to 24m/min) can be achieved with a lower electrical power consumption The Cyclo gearbox allows to reach a mechanical efficiency that is up to two times higher than traditional gearboxes. A substantial reduction of power dissipation is also achieved 24m/min

13. Main features of the new FAAC Cyclo gearbox:  1/49 reduction  Requires half of the power with respect to the other products on the market  DELRIN 100ST (Super Tough) made pinion, very high resistant acetal resin:  Very high mechanical resistance (impact, stiffness, traction)  Auto-lubricant surface  High resistance to atmospheric agents (UV, humidity, etc.) and temperature changes  Used for more than 40 years in automotive, chemical and electrical industries (some examples on the side) Cyclo gearbox

14. Installation of C720 operator: Due to the new reduction principle, the dimensions of the C720 pinion are slightly different from traditional operators. OperatorDistance base-fittings 74090 mm 746112 mm (Z16) or 120 mm (Z20) C720100 mm Cyclo gearbox However, the use of the nylon rack with invertible fittings (see figure on the side) makes the installation parameters comparable to traditional gearmotors (see the table below).

15. Control board E720 Which are the main characteristics of the board?  Easy to configure through the seven-segment display  Highly configurable and easy parameter adjustment  Integrated “virtual” electronic Encoder for safety enhancement  Compatible with a big range of transmitters and receivers (DS, SLH, LC/RC) through the OMNIDEC technology  Both traditional and Bus photocells can be connected to the board

16. High programmability:  50 strength levels  12 logics  ESemiautomatic  EPSemiautomatic “Step”  AAutomatic  A1Automatic1  APAutomatic “Step”  AtAutomatic with timer function  SAutomatic “Safety devices”  SPAutomatic Safety devices “Step”  SAAutomatic with reverse during pause  BSemiautomatic “b”  bCMixed (AP pulse/CH dead-man)  CDead-man  10 speeds (separated for opening and closing)  1° e 2° level programming  The firmware can be updated using a USB cable Control board E720

17. Wide range of available accessories:  Up to 16 couples of photocells can be connected with the BUS-2EASY technology  Traditional photocells can also be connected  Nickel-Metal Hydride emergency batteries (XBAT)  Max current for accessories 500mA at 24Vdc – BUS2EASY max 500mA  Magnetic limit-switches Control board E720

18. High connectivity and flexibility:  The E720 is compatible with the whole range of FAAC photocells PHOTOSWITCH PHOTOBEAM SAFEBEAM XP15B XP15W Wireless  The E720 is compatible with the whole range of FAAC transmitters through the XF module XF Module T2 SLH DL2 SLH XT2 SLH T4 SLH DL4 SLH XT4 SLH Control board E720 XT4 RC DS

19. X-BAT: NiMH (Nickel-Metal Hydride)  Higher longevity than the traditional Seal Lead-Acid (SLA) batteries  NiMH batteries maintain a usable voltage range for a greater time than SLA batteries (see picture below)  More environmentally friendly (they don’t contain lead)  No Memory effect as traditional SLA batteries  Better space safe, compact sizes Control board E720

20. Design Attractive Following the new FAAC family look: D istinctive S imple C lean

21. L : apart from the engine, this dimension must accommodate the transformer, the emergency battery (XBAT) and the fixing holes for the foundation plate. Unlike in the 740, 746 and 844, the fixing holes are inside the case. Seems empty? Not true, the dimensions have been carefully designed and they directly come from the following technical motivations: D : due to the total length of reduction + motor + pinion. H D L Design Studied H : due to the pinion’s height (Z28), the control board (which is mounted in a vertical position for easiness of access, programming and water resistance), and the motor release handle (which is vertical to allow an easier release operation) In general, the wide space availability makes installation and configuration very comfortable for the installer.

22. Ergonomic Design Vertical motor release handle, more convenient and ergonomic.

23. Summary  Why a 24V operator?  Strong points  Technical specifications

24. Technical specifications Power supply230 Vac 50 Hz Motor supply24 Vdc Power170 W Current7 A (24V) Electric motor3200 rpm Max torque18 Nm Thrust320 N PinionZ28 M 4 Gate speedMin 8 / Max 24 m/min Operating ambient temperature-20°C +55°C Weight6 Kg Limit switchesMagnetic Protection classIP 44 Dimensions (L x P x H)300 x 180 x 280

25. Summary  Why a 24V operator?  Strong points  Technical specifications  GS Mark

26. GS mark The C720 operator has been recognized with the GS quality mark, which indicates that it was tested by a third part (Nemko Institute) and it complies with the requirements of the German Equipment and Product Safety Act. The GS is a voluntary mark, but it’s not a self- certification like EN Tested (used by our competitors) and it should not be confused with the CE mark. GS MarkCE Mark VoluntaryCompulsory Appears only on certified products Appears on all the products that are subjected to directives Verification and certification through lab tests performed by a third part (notified body) The tests execution is assumed but not proved The third part Institution continuously checks the product and its production for the whole certification period No checks and no market advantages, since it’s just a self-certification of compliance made by the producer GS Mark: a proof of real safety and product compliance, product USPs CE mark: a commercial mark that assumes the product compliance