1. Shanghai Jiao Tong University 1 GEOMETRIC DIMENSIONING & TOLERANCING (GD & T) ME 250: Design & Manufacturing I School of Mechanical Engineering

2. Shanghai Jiao Tong University 2 Outline Tolerance Definitions Datums Form Controls Rules for Tolerancing Location Control Orientation Controls Runout Controls Profile Controls Surface Finish

3. Shanghai Jiao Tong University 3 Rules for Tolerancing RULE-1: For features-of-size, where only a size dimension is specified, the surfaces shall not extend beyond a boundary (envelope) of perfect form at MMC. “perfect form” means perfect flatness, straightness, circularity, cylindricity.

4. Shanghai Jiao Tong University 4 Rule-1 for Tolerancing

5. Shanghai Jiao Tong University 5 Rule-1 for Tolerancing Rule-1 applies to all feature-of-size (and only to feature-of-size) on a drawing. Rule-1 says that a feature-of-size must have perfect form if the feature-of-size is at MMC. If the part was at less than MMC, a form error equal to the amount of departure would be permissible. If the part was at LMC, a form error equal to the amount of departure would be permissible.

6. Shanghai Jiao Tong University 6 The Term of RFS The Regardless of Feature Size (RFS) is when a geometric tolerance (or datum) applies independent of the feature size. That is, the geometric tolerance is limited to the stated amount regardless of the size of the feature-of-size.

7. Shanghai Jiao Tong University 7 Rules for Tolerancing

8. Shanghai Jiao Tong University 8 Rules for Tolerancing

9. Shanghai Jiao Tong University 9 Exercise in Class If the block was at MMC, what would its straightness be limited to? the flatness of surface A be limited to? If the block was at LMC, the flatness of surface A would be limited to and the flatness of surface B would be limited to. Could both of these flatness conditions exist simultaneously? Why ? If the block was at LMC and the flatness of surface A was 0.3, what would the flatness of surface B would be limited to?

10. Shanghai Jiao Tong University 10 Location Control

11. Shanghai Jiao Tong University 11 Boundary for Surface of Hole

12. Shanghai Jiao Tong University 12 Location Control

13. Shanghai Jiao Tong University 13 Location Control

14. Shanghai Jiao Tong University 14 Orientation Controls Perpendicularity Angularity Parallelism Always uses a datum surface

15. Shanghai Jiao Tong University 15 Perpendicularity

16. Shanghai Jiao Tong University 16 Perpendicularity

17. Shanghai Jiao Tong University 17 Runout Controls Circular runout Total runout Always uses a datum surface

18. Shanghai Jiao Tong University 18 Runout Tolerance

19. Shanghai Jiao Tong University 19 Circular runout

20. Shanghai Jiao Tong University 20 Total runout

21. Shanghai Jiao Tong University 21 Profile Controls Profile of a line Profile of a surface May uses a datum surface

22. Shanghai Jiao Tong University 22 Profile of a Surface

23. Shanghai Jiao Tong University 23 Profile of a Surface

24. Shanghai Jiao Tong University 24 Surface Finish We control the sizes and shape (GD&T) of parts in order to make them fit. We control surface textures in order to make the parts work Fatigue Fiction Wear

25. Shanghai Jiao Tong University 25 Surface Roughness Surface Roughness refers to the fine irregularities (scale smaller than that of waviness) on the surface and is a result of the manufacturing process used. It is measured (by surface profilometers) in terms of height, width and distance on the surface.

26. Shanghai Jiao Tong University 26 Surface Finish Surface finish impacts: How well a surface will withstand pressure, friction and wear How well it will hold and disreibute a lubricant How it will change over use How it will seat or seal How it will conduct electricity, reflect light, accept paint/plating, etc How it will change by further manufacturing processes

27. Shanghai Jiao Tong University 27 Terminology R a (AA): Arithmetic mean/average R q (RMS): Root mean square

28. Shanghai Jiao Tong University 28 Considerations for Surface Roughness Reasons/ Considerations for different surface roughness in design Precision requirements on mating surfaces (seals, fittings, bearings, etc.) frictional considerations (effect of roughness on friction, wear, lubrication) Fatigue and notch sensitivity Resistance (electrical/thermal contact resistance corrosion resistance) Subsequent processing (painting, coating, etc.) Appearance Cost