1. 目录 8 in 1 Sensor ◆ 8 in 1 Sensor Unique Features ● Built in PIR motion sensor and light intensity sensor ● Built in 2 Dry Input Ports ● Built in 32 Logics ● Infrared receiver ● Infrared transmitter ● Built in security alarm logic (work with Security Module)

2. Subnet ID and Device ID Remark MAC Address Basic information

3. 1.Input key target Qty 3.Select IR code from database 2.Select key no. 4.Downlaod 5.Confirm IR Code download

4. 6.Select key no. 7. Select key stroke type IR Code testing 8. Press Transmit and test

5. IR Code receiving 1.Configuration same as switch panel, first select key no. of remoter 2.Setup the mode for the key

6. 3.Select key control mode 4.Save IR Code receiving

7. 5.Select control target IR Code receiving

8. 6.Input target Subnet ID, Device ID and Parameter 7. Save IR Code receiving

9. 8. Align the Remoter with 8 in 1 sensor, press the key and test

10. 1. Select a Logic Block (Max 32 blocks) 2.Input Remark and charge the status to Valid, default is invalid 3. Save 4.Click Edit to setup menu Automation logics configuration

11. Current status Select logic conditionSelect logics relation Command

12. Application In case of a meeting room has below requirements: 1.When people open the door and come in the meeting room, the lights open automatically 2. After people come in the room for more than 1 minute, open the AC and change the temperature to 25 ℃ 3. After people leave the room for 1 minute, off the lights and the temperature increase 2 ℃ 4.After people leave the room for 3 minute, turn off the AC automatically We need 4 logic blocks to accomplish the requirements above

13. 1.When people open the door and come in the meeting room, the lights open automatically Requirements

14. 2. Input remark and change current status to Valid 3.Save 4.Edit Logic setting 1.Select a Logic block

15. Requirement: When people open the door and come in the meeting room, the lights open automatically 5.If the door installed a magnetic contact and connect to 8 in 1 sensor, change condition to disconnect 6. Select Motion sensor and Condition movement 7. Change delay time to 0 sec. 8.Select relation And 9.Save logic setting 10.Click Command to select control target

16. 11. Input light channel to open 12.Save Requirement: When people open the door and come in the meeting room, the lights open automatically

17. 2. After people come in the room for more than 1 minute, open the AC and change the temperature to 25 ℃ Requirements

18. Requirement: After people come in the room for more than 1 minute, open the AC and change the temperature to 25 ℃ 2. Input remark and change current status to Valid 3.Save 4.Edit Logic setting 1.Select a Logic block

19. 5.If the door installed a magnetic contact and connect to 8 in 1 sensor, change condition to disconnect 6. Select Motion sensor and Condition movement 7. Change delay time to 1 minutes 8.Select relation And 9.Save logic setting 10.Click Command to select control target Requirement: After people come in the room for more than 1 minute, open the AC and change the temperature to 25 ℃

20. 12.Input target with the subnet ID and device ID of the sensor. Type “Infrared remote sensor", parameter 1 “3”, parameter 2 “on” 13.Save Requirement: After people come in the room for more than 1 minute, open the AC and change the temperature to 25 ℃ 11.Before set the control target, please go to IR transmitter page and record the key no.(3) of 25 ℃

21. 3. After people leave the room for 1 minute, off the lights and the temperature increase 2 ℃ Requirements

22. 2. Input remark and change current status to Valid 3.Save 4.Edit Logic setting 1.Select a Logic block Requirement: After people leave the room for 1 minute, off the lights and the temperature increase 2 ℃

23. Requirement: After people leave the room for 1 minute, off the lights and the temperature increase 2 ℃ 5.Select Motion sensor and Condition No movement 6.Change delay time to 1 minutes 7.Select either AND or OR because there’s only one logic condition 8.Save logic setting 9.Click Command to select control target

24. 10.Input target with the subnet ID and device ID of the sensor. Type “Infrared remote sensor", parameter 1 “5”, parameter 2 “on” 11.Save Requirement: After people leave the room for 1 minute, off the lights and the temperature increase 2 ℃

25. 4.After people leave the room for 3 minute, turn off the AC automatically Requirements

26. 2. Input remark and change current status to Valid 3.Save 4.Edit Logic setting 1.Select a Logic block Requirement: After people leave the room for 3 minute, turn off the AC automatically

27. 5.Select Motion sensor and Condition No movement 6.Change delay time to 3 minutes 7.Select either AND or OR because there’s only one logic condition 8.Save logic setting 9.Click Command to select control target Requirement: After people leave the room for 3 minute, turn off the AC automatically

28. 10.Input control target 11. Save Requirement: After people leave the room for 3 minute, turn off the AC automatically

29. Complete