Presentation is loading. Please wait.

Presentation is loading. Please wait.

1. Take HV harnesses with label (IHV2) and transfer on the Stacking table. 1.1 Inspect HV harnesses visually. 2.1 Insulate HV Flex with 3M™ VHB™ Tape.

Published byMarilyn Rodgers Modified over 8 years ago

Similar presentations

Presentation on theme: "1. Take HV harnesses with label (IHV2) and transfer on the Stacking table. 1.1 Inspect HV harnesses visually. 2.1 Insulate HV Flex with 3M™ VHB™ Tape."— Presentation transcript:

1

2 1. Take HV harnesses with label (IHV2) and transfer on the Stacking table. 1.1 Inspect HV harnesses visually. 2.1 Insulate HV Flex with 3M™ VHB™ Tape and kapton. (3M™ Tape + Kapton+ 3M™ Tape, Use VHB ™ Tape Surface Preparation Technical Bulletin ) 2.2 Do not remove the foil from the latest 3M ™ Tape. 2.3 Separate harness in the channel. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 2.2 Inspect HV harnesses visually and check voltage.

3 3. Take HV harnesses pin board with label (IHV1) and transfer it on the table. 4. Inspect HV harnesses visually. 4.1 Insulate HV Flex with 3M™ VHB™ Tape and kapton. (3M™ Tape + Kapton+ 3M™ Tape, Use VHB ™ Tape Surface Preparation Technical Bulletin) 4.2 Do not remove the foil from the latest 3M ™ Tape. 5.1 Inspect HV harnesses visually and check voltage. 5.3 Remove the foil from the latest 3M ™ tape and laminate together HV tape.

4 6.Take HV harnesses with label (IHV1) and transfer on the Stacking table. 7.Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 8. Inspect HV harnesses visually and check voltage. 9.Pre-laminate together HV harnesses with label (IHV2) and label (IHV1) with 3M™ VHB™ Tape. (Use VHB ™ Tape Surface Preparation Technical Bulletin) 9.1 Check the position Penetration Flex before laminating.

5 8. Take NTC harnesses pin board with label (NTC2) and transfer it on the table. 9. Inspect NTC harnesses visually. 10. Insulate NTC Flex with 3M™ VHB™ Tape and kapton. (3M™ Tape + Kapton+ 3M™ Tape, Use VHB ™ Tape Surface Preparation Technical Bulletin) 10.1 Do not remove the foil from the latest 3M ™ Tape. 11.Transfer NTC harnesses with label (NTC2) on the Stacking table. 12. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 13. Inspect NTC harnesses visually and check voltage. 14. Remove the foil from the latest 3M ™ tape and laminate together HV and NTC tape.

6 15.Take NTC harnesses pin board with label (NTC1) and transfer it on the table. 16. Inspect NTC harnesses visually. 17. Transfer NTC harnesses with label (NTC1 ) on the Stacking table. 18. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity) 19. Inspect NTC harnesses visually and check voltage 20. Remove the foil from the latest 3M ™ tape and laminate together NTC tape. (Use VHB ™ Tape Surface Preparation Technical Bulletin) 21. Fix every bunch of wires. transfer plate

7 22. Transfer NTC/HV harness stacking to the soldering table. 22.1 Use the device to transfer NTC/HV harness.

8 Potential problems with the wiring bundles

9 23. Transfer ISP harnesses with label (ISP3) on the Stacking table. 24. Inspect IPS harnesses visually and check voltage. 25. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 26. Insulate ISP3 Flex with 3M™ VHB™ Tape and kapton. 26.1 Use VHB ™ Tape Surface Preparation Technical Bulletin. 26.2 Do not remove the foil from the latest 3M ™ Tape. 27. Take IPS harnesses pin board with label (ISP2) and transfer it on the Stacking. 28. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 29. Inspect IPS harnesses visually and check voltage. 30. Remove the foil from the 3M ™ tape and laminate together ISP tape. 30.1 Use VHB ™ Tape Surface Preparation Technical Bulletin. 31. Take IPS harnesses pin board with label (ISP1) and transfer it on the Stacking. 32. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 33. Inspect IPS harnesses visually and check voltage. 34. All IPS harnesses Insulate kapton tape and Pre-laminate together with 3M™ VHB™ Tape. 34.1 Use VHB ™ Tape Surface Preparation Technical Bulletin. kapton tape 3M™ VHB™ Tape kapton tape

10 35. Separate harness the top and bottom PP0 Flex Flat. ( HV on the bottom PP0 Flex Flat, NTC on the top ). 36. Inspect harnesses visually and check voltage. 37. Cut NTC/HV harness. 38. Soldering NTC harness. (Use INNER SERVICE PANEL PP0 to PP1B Connectivity Plan) 39. Transfer ISP harness stacking to the soldering table. 40. Inspect harnesses visually and check voltage. 41. Cut ISP harness. 42. Soldering ISP harness. (Use INNER SERVICE PANEL PP0 to PP1B Connectivity Plan) 43. Install the ISP Corrugated Panel and ISP Bottom Panel, 44. Fix the wire in the ISP Corrugated Panel. 44.1 Install a carbon panel. 44.2 Soldering ENV connectors. 44.3 Fix ENV wire on the carbon panel. 45. Overturn harness. 46. Soldering HV harness. (Use INNER SERVICE PANEL PP0 to PP1B Connectivity Plan ) 47. After all soldering, transfer ISP Panel to the stacking table. cut soldering table

11 48. Fix the wires on the PP0 Panel. 49. Use the tools and tape for correctly installation of the wires. 50. Take up Extra length wires to the corrugated panel. 51. Fix the wires with glue. glue. tape tools

12 52. Final bonding flange 53. Spray silicone on the tool. 54. Install ½ flanges in device. 55. Put glue on stacks and 2 shims. 56. Fix stacking in the tool. 57. Install Tool for bending. 58. Bend the bundles. Tool for bending

Download ppt "1. Take HV harnesses with label (IHV2) and transfer on the Stacking table. 1.1 Inspect HV harnesses visually. 2.1 Insulate HV Flex with 3M™ VHB™ Tape."

Similar presentations

F AST T RACK REMOTE SWITCH WIRING SET UP FOR THE LIGHT BoardPlug Power strips relay Wiring Harness.

F AST T RACK REMOTE SWITCH WIRING SET UP FOR THE LIGHT BoardPlug Power strips relay Wiring Harness.
Routed Systems Presented by: Bassam Najar, Design Engineer Butler International Inc.

Routed Systems Presented by: Bassam Najar, Design Engineer Butler International Inc.
Equipment for Assembly Fluke Multimeter 115 True RMS Glue Ring Jig Flathead screwdriver 60 Watt desk lamp HIOS Cl 4000 Electric screw driver Anti-static.

Equipment for Assembly Fluke Multimeter 115 True RMS Glue Ring Jig Flathead screwdriver 60 Watt desk lamp HIOS Cl 4000 Electric screw driver Anti-static.
CricketSat Assembly.

CricketSat Assembly.
Assembling a Functional Multi-Wire Proportional Counter - Page 1 Work in pairs. One person will take the chamber apart, and the other will reassemble it.

Assembling a Functional Multi-Wire Proportional Counter - Page 1 Work in pairs. One person will take the chamber apart, and the other will reassemble it.
Procedures during Tracker Connection WPA meeting 3 rd December 2007, Michael Eppard, CERN Installation sequence Manpower needs for installation work.

Procedures during Tracker Connection WPA meeting 3 rd December 2007, Michael Eppard, CERN Installation sequence Manpower needs for installation work.
1 Ladder assembly steps HFT PIXEL updated for ultimate chip ladders 2/12/2012 ladder fixture u.SLDASM.

1 Ladder assembly steps HFT PIXEL updated for ultimate chip ladders 2/12/2012 ladder fixture u.SLDASM.
AMS-02 tracker mechanics status of assembly and integration at UniGe Outer planes: - Tests of evaporator (cooling loop) integration - Tools to develop.

AMS-02 tracker mechanics status of assembly and integration at UniGe Outer planes: - Tests of evaporator (cooling loop) integration - Tools to develop.
Wire bundles connecting to Keyence Sensors (screw plug on other end) Colored Wires from bundles (brown, blue, white are nonfunctional, cap with scotch.

Wire bundles connecting to Keyence Sensors (screw plug on other end) Colored Wires from bundles (brown, blue, white are nonfunctional, cap with scotch.
Plan for MRPC Production Yongjie Sun Center of Particle Science and Technology University of Science and Technology of China.

Plan for MRPC Production Yongjie Sun Center of Particle Science and Technology University of Science and Technology of China.
1 Student Hands On Training I (2009) Construction, Integration, and Test Construction, Integration, and Test.

1 Student Hands On Training I (2009) Construction, Integration, and Test Construction, Integration, and Test.
November 6 2002Vertex 2002 Kazu Hanagaki1 Layer 0 in D0 Silicon Tracker for run2b Kazu Hanagaki / Fermilab for D0 run2b Silicon Tracker group Motivation.

November Vertex 2002 Kazu Hanagaki1 Layer 0 in D0 Silicon Tracker for run2b Kazu Hanagaki / Fermilab for D0 run2b Silicon Tracker group Motivation.
PRR TRD COOLING A. Marín (GSI) 7/01/2004 ALICE PRR TRD COOLING P.Glässel, A.Marín, V.Petracek, J.Stachel, M.R.Stockmeier, J.P.Wessels ALICE PRR TRD COOLING.

PRR TRD COOLING A. Marín (GSI) 7/01/2004 ALICE PRR TRD COOLING P.Glässel, A.Marín, V.Petracek, J.Stachel, M.R.Stockmeier, J.P.Wessels ALICE PRR TRD COOLING.
GLAST LAT ProjectF2F, June 15, 2005 GLAST Large Area Telescope: Performance & Safety Assurance Joseph Cullinan SLAC Performance & Safety Assurance Manager.

GLAST LAT ProjectF2F, June 15, 2005 GLAST Large Area Telescope: Performance & Safety Assurance Joseph Cullinan SLAC Performance & Safety Assurance Manager.
1 Module and stave interconnect Rev. sept. 29/08.

1 Module and stave interconnect Rev. sept. 29/08.
MM mechanical prototype Work progress at CERN MicroMegas General Meeting, CERN, 5-6 November 2013 1.

MM mechanical prototype Work progress at CERN MicroMegas General Meeting, CERN, 5-6 November
Institute Of Applied Technology ATE 1012 Grade 10 Eng. Rose Hasan.

Institute Of Applied Technology ATE 1012 Grade 10 Eng. Rose Hasan.
Basic Soldering Tips and Techniques! RM1B. Before starting the construction of a soldering project, be sure that your soldering iron tip is in good shape!

Basic Soldering Tips and Techniques! RM1B. Before starting the construction of a soldering project, be sure that your soldering iron tip is in good shape!
Technology-Assisted Assessment Inquiry Part 1

Technology-Assisted Assessment Inquiry Part 1
Weld Types - Lap Weld UVU CRT 2009. Lap Weld  Many automotive structural panels are assembled using a lap joint.  Technicians must make test welds visually.

Weld Types - Lap Weld UVU CRT Lap Weld  Many automotive structural panels are assembled using a lap joint.  Technicians must make test welds visually.

Similar presentations

Ads by Google