Download presentation
Presentation is loading. Please wait.
Published byShannon King Modified over 9 years ago
1
第 3 部分 模具设计 Part 3 Mould Design 成型零件 Moulding Component 温控系统 Temperature Control System 导向与定位机构 Guiding and Positioning Mechanism 顶出机构 Ejector Unit
2
成型零件 Moulding components 1. 构建热塑件 Build hot parts 使用特征 -> 缩放比例,常用 ABS 收缩率: 1.005 ; 2. 构建模芯 Build mould inserts. 使用曲面 -> 等距曲面 ( 距离为 0) 抽取塑件外表面 / 内表面; 使用曲面 -> 平面区域等命令填补缺口面; 使用曲面 -> 平面区域建立型腔 / 型芯外围压紧配合面; 使用曲面 -> 缝合曲面将以上所有面缝合成整张曲面; 使用拉伸命令将型腔 / 型芯外围轮廓拉伸出方料; 使用切除 -> 使用曲面,利用整张曲面截切方料得到型腔 / 型芯。 3. 设置浇注系统与顶针孔 Setup feeding system & ejector pin holes 4. 分割模芯 Divide up mould inserts
3
构建热塑件 Build hot parts
4
抽取外表面 Get outside surfaces
5
填充孔形 Fill holes
6
设置分型面 Setup parting surface
7
切割型面 Cut mould surfaces
8
浇注系统与顶针孔 Feeding system & ejector pin holes
9
分割模芯 Divide up mould inserts
10
整体式型腔 Integral cavity 整体嵌入式型腔 Integral embedded cavity
11
局部镶拼式型腔 Local insertion and splice cavity 嵌拼式型腔 Split-type cavity
12
温控系统 Temperature Control System
14
高光无痕注塑模具近形介质通道模型
15
不同材料制高光面壳随形传热分析 无支撑高光面壳大三角随形槽高光面壳 铜合金 铝合金 结构钢 不同钢 塑料
16
定模模芯近随形介质通道设计方案
17
1 .导柱与导套 Guide bush & Guide pin 导柱与导套对定模与动模及有关模板(流道板、脱模板等) 起到导向定位作用,在模具组装时也兼起保护型芯的作用。 为了确保合模后分型面良好贴合,导柱与导套在分型面处 应设置承屑槽:一般都是削去一个面,或在导套的孔口倒角。 导柱工作部分的长度应比型芯端面高出 6 ~ 8 mm 。 导向与定位机构 Guiding and Positioning Mechanism
18
2 .锥面定位机构 Cone precise positioning mechanism 1. 螺栓 bolt; 2 、 9. 锥面定位套 cone precise positioning bush; 3. 定模板 fixed mould plate 4. 锥面定位芯 Cone positioning pin; 5. 动模板 moving mould plate; 7 、 8. 压块 gasket
19
3 .斜面精定位机构 Bevel precise positioning mechanism 1. 定模 fixed mould; 2. 定位滑块 positioning slide wedge 3. 动模 moving mould 1. 定位滑块 positioning slide wedge 2. 耐磨块 wear-resisting plate 单斜面 Single-bevel 双斜面 Double-bevel 单斜面 Wear-resisting plate bevel
21
顶出机构 Ejector Unit 1. 动模座板 moving mould clamping plate; 2. 顶针垫板 ejector support plate; 3. 顶针 ejector pin; 4. 回程杆 return pin; 5. 动模板 moving mould plate; 6. 顶针固定板 ejector retainer plate;
22
1. 顶针 ejector pin; 2. 顶针垫板 ejector support plate; 3. 顶针固定板 ejector retainer plate; 4. 顶块 ejector block; 5. 型芯 core; 6. 回程杆 return pin
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.