1. Eclipse HX E-QUE trunking card

2. Company Confidential 2 Eclipse HX E-QUE CARD More details are available in the Omega installation manual E-QUE – E1 / Trunking card E1/T1 card with dual connection to telecom leased lines. Each E1 controller provides 30 digital audio lines.  E1 is a 2Mb telecom standard that allows for 30 digital channels over CAT5 cabling  T1 is a 1.5Mb telecoms standard that allows for 24 digital channels over CAT5 cabling  The E-QUE card conforms to standard telecoms standards, it can be interconnected to 3 rd party devices like E1-to-IP muxs, E1-to-Fibre, E1-to-ATM The ClearCom E-QUE card can be used to pass audio G.711(3Khz) or G.722 (7Khz) across the E1/T1 channel allowing for  Hi-capacity trunklines between matrices  Hi-capacity audio tie-lines between matrices or 3 rd party devices that support E1 Ethernet data Matrix A, Matrix B, E1 (2Mb) trunklines

3. Company Confidential 3 Note: The E-QUE card is a very versatile card and can be used in a number of different modes.  FreeSpeak mode  E1 – Trunking mode  E1 – Direct 4wire external mode  T1 – Trunking mode  The same card can be used in only one mode  Up to a maximum of 4x E-QUE cards can be fitted into a matrix (in either E1 or FreeSpeak mode) E-QUE – E1 / Trunking card Eclipse HX E-QUE CARD More details are available in the Omega installation manual

4. Company Confidential 4 The E-QUE E1/T1 card can be configured using HX The EQUE E1 card can only be used in Eclipse HX Omega or Median frames  Select the required card type from the Setup matrix hardware screen  Select the Card properties link to change the codec setting  If used for networking 2 matrices – then switch to “My systems” screen and link the E1 cars together HX PROGRAMMING Eclipse HX E-QUE CARD More details are available in the Omega installation manual

5. Company Confidential 5 E-QUE – FRONT AND REAR FEATURES Eclipse HX E-QUE CARD More details are available in the Omega installation manual  LAN connector for upgrading  RJ45 #1 for E1 controller  RJ45 #5 for E1 controller  E1 connector pin-out

6. Company Confidential 6 The E-Que card can be used for both direct E1 to E1 port connections or to provide trunk linking via a network between systems. The E1 connections can be made between Eclipse HX systems or between Eclipse HX systems and compatible third-party equipment. E1 mode provides 30 channels of G.711 or G.722 encoded audio are available on each port, giving 60 channels per card. T1 mode provides 24 channels of G.711 or G.722 encoded audio are available on each port, giving 48 channels per card. E-QUE – E1 TRUNK AND DIRECT MODES Eclipse HX E-QUE CARD More details are available in the Omega installation manual The E1 specifications are:  HDB3 Encoding  Long Haul Receive Signal Level  E1 120 Ohm Tx Pulse Amplitude  Balanced RJ45 connection  120 Ohm Line Impedance  No Signalling  G.722 64 kbit/s Audio Encoding  Tx Clock locally generated  Rx Clock Line Recovered The T1 trunking specifications are:  B8ZS Encoding  Long Haul Receive Signal Level  T1 Long Haul (LBO 0 dB) Tx Pulse Amplitude  Balanced RJ45 connection  120 Ohm Line Impedance  No Signalling  G.722 64 kbit/s Audio Encoding  Tx Clock locally generated  Rx Clock Line Recovered  Extended Super Frame

7. Company Confidential 7 Matrices linked locally by E1 crossover cable E-QUE – E1 APPLICATIONS Eclipse HX E-QUE CARD More details are available in the Omega installation manual Matrices linked remotely by E1 network (leased lines) via mux

8. Company Confidential 8 Matrix linked to 3 rd party device like a voice recorder or transceiver Eclipse HX E-QUE CARD More details are available in the Omega installation manual E-QUE – E1 APPLICATIONS

9. Thank you!