1. 1 Automotive Shop Safety R. Bortignon Automotive Shop Safety R. Bortignon

2. 2 Personal Protective Equipment  eye protection must be worn in the shop at all times!

3. 3 Two types of eye protection you can use…  safety glasses: must be worn at all times  face shield

4. 4 Use ear protection…  air chisel

5. 5 Hand Protection

6. 6 Protecting Your Lungs… If you are replacing brake friction material or a clutch, vacuum the dust with a hepa filter vacuum and wash down the area with water/brake cleaner before working… DO NOT USE COMPRESSED AIR! Brake linings & clutch discs may contain asbestos!

7. 7 Protecting Your Lungs Exhaust “donuts” & some cylinder head gaskets contain asbestos!

8. 8 Do’s and Don'ts  No open-toed shoes  Closed toe footwear only!  Remove any rings, watches, bracelets or long necklaces before working in the shop (can cause burns, shock, and pull you into rotating parts!)  Coveralls or a shop coat should be worn

9. 9 Long hair needs to be tied back !

10. 10 Exhaust Gases Carbon Monoxide is…  Colorless  Odorless  Deadly  When we run a vehicle in our shop, we have to protect ourselves by using the exhaust retraction system  How do you turn it on?

11. 11 Exhaust Retraction System

12. 12 Air Guns & Sockets  When using the air gun, use the black impact sockets…  Not the chrome sockets!

13. 13 Dangers Under the Hood…  radiator fans (2 types)…  electric  belt driven

14. 14 Burn Hazards! The following items can cause burns to your hands or face… The following items can cause burns to your hands or face… radiator capradiator cap  coolant is >100°C  coolant is pressurized  don’t remove it unless it’s cold to the touch! exhaust manifoldexhaust manifold  exhaust gases are >1000°C catalytic convertercatalytic converter  very hot

15. 15 Fire Hazards Flammable or combustible items…  fuel  oil/lubricants  cleaning solvent: (use rubber gloves)  WD40, paint etc. must be stored in a flammable materials cabinet must be stored in a flammable materials cabinet not like this…

16. Brake Fluid Is a very special fluid with certain properties, such as…Is a very special fluid with certain properties, such as…  Poisonous  Harmful to your eyes (wash with water)  Hygroscopic (absorbs moisture, which can ruin your brakes over time  Will also eat paint when left in contact with it 16

17. Air Conditioning Never disconnect air conditioning linesNever disconnect air conditioning lines Contact with Freon will cause burns to your skin and permanent eye damageContact with Freon will cause burns to your skin and permanent eye damage Burning Freon gas creates Phosgene gas which causes permanent respiratory damage.Burning Freon gas creates Phosgene gas which causes permanent respiratory damage. 17

18. 18 Fuel Vapors & Fires Anytime the fuel system is disconnected (fuel tank, carburetor, fuel pump, fuel injectors etc.), fuel vapors are present.Anytime the fuel system is disconnected (fuel tank, carburetor, fuel pump, fuel injectors etc.), fuel vapors are present. Prevent fires by… Prevent fires by…  disconnecting the negative battery terminal keep sparks away from the fuel vaporskeep sparks away from the fuel vapors watch those working around youwatch those working around you have a fire extinguisher nearbyhave a fire extinguisher nearby

19. Gasoline Safety Do not use gasoline as a solvent. Do not use gasoline as a solvent. Use a solvent/varsol as a cleaning agent (still flammable). Use a solvent/varsol as a cleaning agent (still flammable). Only store gasoline in approved containers and in small quantities. Only store gasoline in approved containers and in small quantities. Use caution when transferring gasoline. Use caution when transferring gasoline. Do not weld on a vehicle with a damp/leaking fuel line or fuel tank. Do not weld on a vehicle with a damp/leaking fuel line or fuel tank. Never start a gasoline siphon with your mouth. Never start a gasoline siphon with your mouth. Never add fuel to an engine while cranking. Never add fuel to an engine while cranking. Never look down a carburettor if the car is running. Never look down a carburettor if the car is running. 19

20. Electrical Equipment Do not use electrical equipment that has a frayed or damaged cord. Do not use electrical equipment that has a frayed or damaged cord. Make sure all electrical equipment is off before you plug it in. Make sure all electrical equipment is off before you plug it in. Do not leave or use electrical equipment on wet floors. Do not leave or use electrical equipment on wet floors. Do not play with drop cords. Do not play with drop cords. Do not overload power tools. Do not overload power tools. Use caution with trouble lights - electrically hot socket; may break and start fire if contacted with gas. Use caution with trouble lights - electrically hot socket; may break and start fire if contacted with gas. Unplug by pulling on plug, not the cord. Unplug by pulling on plug, not the cord. 20

21. Carline – Maple Ridge - 2009 21

22. 22

23. Vancouver - December, 2009

24. Painting Must be done in a well ventilated areaMust be done in a well ventilated area Away from flames and sparksAway from flames and sparks Never put an aerosol can in the fire, it will explode!Never put an aerosol can in the fire, it will explode!

25. 25 Other Fire Hazards… Oily, greasy or fuel soaked items must be placed in the fire- proof rag container when you are finished using them!Oily, greasy or fuel soaked items must be placed in the fire- proof rag container when you are finished using them! Change out of gas/oil soaked overalls/clothingChange out of gas/oil soaked overalls/clothing Keep coveralls clean to prevent spontaneous combustionKeep coveralls clean to prevent spontaneous combustion

26. Batteries Are always to be considered dangerousAre always to be considered dangerous Contain acid, give off explosive gasses, and can electrocute you!Contain acid, give off explosive gasses, and can electrocute you!

27. Battery Safety Keep all sparks/flames/naked flame light sources away from hydrogen gas which is produced by a charging battery.Keep all sparks/flames/naked flame light sources away from hydrogen gas which is produced by a charging battery. Always have the battery charger unplugged prior to connecting or disconnecting it.Always have the battery charger unplugged prior to connecting or disconnecting it. Always disconnect battery when welding on a vehicleAlways disconnect battery when welding on a vehicle Do not use top of battery as a tool storage.Do not use top of battery as a tool storage. Use proper method for connecting or disconnecting a battery charger, jumper cables and battery cables.Use proper method for connecting or disconnecting a battery charger, jumper cables and battery cables. Keep battery acid away from clothes, skin and vehicle paint.Keep battery acid away from clothes, skin and vehicle paint. Do not boost a dead 6V battery with a 12V one (you may damage the other cars electrical system)Do not boost a dead 6V battery with a 12V one (you may damage the other cars electrical system) What to do if battery explodes.What to do if battery explodes.  Get the person to sink and wash and rinse skin and/or eyes  Wash vehicle with water 27

28. Battery Cables *Always* disconnect the *ground (-)* cable first.. (black one)*Always* disconnect the *ground (-)* cable first.. (black one) *Connect * the ground cable *last*.*Connect * the ground cable *last*. Jumper Cables *Connect* jumpers to dead battery (keep other end of cables separated).*Connect* jumpers to dead battery (keep other end of cables separated). (Red = +, Black = -)(Red = +, Black = -) *Connect* other end (red lead = +) of good battery and (black = -) to engine block or frame of vehicle with good battery.*Connect* other end (red lead = +) of good battery and (black = -) to engine block or frame of vehicle with good battery. 28

29. Grinder / Wire Wheel Always wear eye protection.Always wear eye protection. Always keep tool rest adjusted close as possible (2mm or 1/8”).Always keep tool rest adjusted close as possible (2mm or 1/8”). Keep fingers away from wheel and hold small parts with vise grips.Keep fingers away from wheel and hold small parts with vise grips. Always use the tool rest to support the work.Always use the tool rest to support the work. Never wear gloves.Never wear gloves. Stand to one side when starting the grinder.Stand to one side when starting the grinder. Allow grinder to reach full operational speed before using.Allow grinder to reach full operational speed before using. Allow grinder to come to a stop on it’s own, do not press on the wheel to slow down the wheel.Allow grinder to come to a stop on it’s own, do not press on the wheel to slow down the wheel. 29

30. Hand tools should… …never be left on the floor…never be left on the floor …be kept clean of oil and dirt…be kept clean of oil and dirt …be kept clear of rotating machinery…be kept clear of rotating machinery …never be placed on top of a battery (BOOM!)…never be placed on top of a battery (BOOM!) …only be used for their intended purpose…only be used for their intended purpose

31. Please Remember… You should use the correct tool, and size of toolYou should use the correct tool, and size of tool Defective tools are to be reported to the TeacherDefective tools are to be reported to the Teacher A pull is safer than a pushA pull is safer than a push

32. 32 Tripping & Slipping Hazards sweep & mop shop floor as you work & at the end of the lab!sweep & mop shop floor as you work & at the end of the lab! floor dry is to be used for large oil spills onlyfloor dry is to be used for large oil spills only keep shop floor free of tripping hazardskeep shop floor free of tripping hazards  storage of parts?  Done with tools?

33. 33 Compressed Air do not use compressed air to clean off clothes & skindo not use compressed air to clean off clothes & skin  at 4”, 40 PSI can rupture an eardrum, cause a brain hemorrhage or death  12psi can pop an eyeball from its socket  4psi in the mouth can rupture a lung or intestine  compressed air entering a small wound on the hand has been known to inflate the arm to the size of a grapefruit  Near the ears can cause pressure changes and hearing loss  Never look into the “business” end!  Never point it towards your body!  Use caution when hooking up air lines  Watch for tripping hazard from air lines  Never spin bearings with compressed air

34. 34 Eye Wash Station Do you know where it is & how to use it?

35. Engines (before starting) Check that they contain oil & coolantCheck that they contain oil & coolant Check under the hood for loose tools, parts, wires, etcCheck under the hood for loose tools, parts, wires, etc Attach and turn on the exhaust extractor fanAttach and turn on the exhaust extractor fan Do Not attempt to start it if there is a gas leakDo Not attempt to start it if there is a gas leak Do Not prime the carb with gas in the shopDo Not prime the carb with gas in the shop Report anything unusual to your instructorReport anything unusual to your instructor

36. 36 Parking Vehicles in Automotive Shops automatic transmission: in park with parking brake onautomatic transmission: in park with parking brake on manual transmission: in neutral with parking brake onmanual transmission: in neutral with parking brake on

37. 37 Moving Vehicles in & Around the Shop Who will move vehicles?Who will move vehicles?  L?  N?  Teacher? Ask Mr Jurica first. Procedures for starting engines & moving cars in/around shopProcedures for starting engines & moving cars in/around shop Lock-out procedures for cars with inoperative brakes, steering etc.?Lock-out procedures for cars with inoperative brakes, steering etc.? Leave the drivers side window rolled down/keys on dash (can’t lock keys inside and can hear instructions)Leave the drivers side window rolled down/keys on dash (can’t lock keys inside and can hear instructions) No radios at any time.No radios at any time.

38. Jacks and Safety Stands Always use safety stands when working on a raised vehicle. Always use safety stands when working on a raised vehicle. Make sure jacks are properly located before lifting. Make sure jacks are properly located before lifting. Ensure jack can adjust position when lifting (wheels are free to roll) Ensure jack can adjust position when lifting (wheels are free to roll) Block the wheels that are touching the ground. Block the wheels that are touching the ground. 38

39. Creeper Boards Mechanics use them to scoot around under vehiclesMechanics use them to scoot around under vehicles Do Not leave them on the ground, stand them up when not on themDo Not leave them on the ground, stand them up when not on them Do Not push them under a car, you may drive over itDo Not push them under a car, you may drive over it

40. Equipment & Power Tools Receive permission to use equipment. Do not use equipment that you have not had instruction in its use. Use all safety devices provided with each piece of equipment. 40

41. Hoists Permission? Permission? Clean lift area/position arms in position. Clean lift area/position arms in position. Drive into correct position for vehicle balance. Drive into correct position for vehicle balance. Block wheels ( drive on hoist ). Block wheels ( drive on hoist ). Make sure lift bars and blocks are properly located before you start the lift. Check lift points/doors/hood to ensure no damage to the vehicle! Make sure lift bars and blocks are properly located before you start the lift. Check lift points/doors/hood to ensure no damage to the vehicle! After lifting just off of ground, rock to check stability. After lifting just off of ground, rock to check stability. After work is done, clear area with a visual and verbal After work is done, clear area with a visual and verbal Raise the car slightly to disengage the safety locks Raise the car slightly to disengage the safety locks Be sure all safety-locks release before Be sure all safety-locks release before lowering a car from the wheel free position. lowering a car from the wheel free position. 41

42. Hoist Safety 42

43. This is not the end! Safety will be stressed in every lesson where it is applicable. You will be expected to act -at all times- in a safe and responsible manner in this shop. You will be expected to act -at all times- in a safe and responsible manner in this shop. If you behave in a manner that seems likely to harm yourself or others, you will be removed from this course at once.

44. Please note… You may not leave the school grounds, or go for a test drive during class time without your instructors permission. Only those students who hold a FULL, valid drivers license may operate a vehicle, in any manner.

45. 45 WHMIS & MSDS Worksafe BCWorksafe BC WHMISWHMIS MSDSMSDS assignmentassignment